ATMEGA169P-16MCH Atmel, ATMEGA169P-16MCH Datasheet - Page 310

• Manufacturer Part Number: ATMEGA169P-16MCH
• Description: MCU AVR 16KB FLASH 16MHZ 64-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169P-16MCH

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.8
8018P–AVR–08/10
Serial Downloading
Table 27-13. Parallel Programming Characteristics, V
Notes:
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out-
put). After RESET is set low, the Programming Enable instruction needs to be executed first
before program/erase operations can be executed. NOTE, in
mapping for SPI programming is listed. Not all parts use the SPI pins dedicated for the internal
SPI interface.
Symbol
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
DVXH
XLXH
XHXL
XLDX
XLWL
XLPH
PLXH
BVPH
PHPL
PLBX
WLBX
PLWL
BVWL
WLWH
WLRL
WLRH
WLRH_CE
XLOL
BVDV
OLDV
OHDZ
1. t
2. t
commands.
WLRH
WLRH_CE
Parameter
Data and Control Valid before XTAL1 High
XTAL1 Low to XTAL1 High
XTAL1 Pulse Width High
Data and Control Hold after XTAL1 Low
XTAL1 Low to WR Low
XTAL1 Low to PAGEL high
PAGEL low to XTAL1 high
BS1 Valid before PAGEL High
PAGEL Pulse Width High
BS1 Hold after PAGEL Low
BS2/1 Hold after WR Low
PAGEL Low to WR Low
BS1 Valid to WR Low
WR Pulse Width Low
WR Low to RDY/BSY Low
WR Low to RDY/BSY High
WR Low to RDY/BSY High for Chip Erase
XTAL1 Low to OE Low
BS1 Valid to DATA valid
OE Low to DATA Valid
OE High to DATA Tri-stated
is valid for the Write Flash, Write EEPROM, Write Fuse bits and Write Lock bits
is valid for the Chip Erase command.
(1)
(2)
CC
= 5V ±10%
Table 27-14 on page
Min
200
150
150
150
150
3.7
7.5
67
67
67
67
67
67
67
0
0
0
0
0
ATmega169P
Typ
Max
250
250
250
4.5
1
9
311, the pin
Units
ms
ns
μs
ns
310