ATMEGA329P-20MN Atmel, ATMEGA329P-20MN Datasheet - Page 50

• Manufacturer Part Number: ATMEGA329P-20MN
• Description: IC MCU AVR 32K 20MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA329P-20MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.5
10.5.1
10.5.2
8021G–AVR–03/11
Register Description
MCUSR – MCU Status Register
WDTCR – Watchdog Timer Control Register
The MCU Status Register provides information on which reset source caused an MCU reset.
• Bit 4 – JTRF: JTAG Reset Flag
This bit is set if a reset is being caused by a logic one in the JTAG Reset Register selected by
the JTAG instruction AVR_RESET. This bit is reset by a Power-on Reset, or by writing a logic
zero to the flag.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the Reset Flags to identify a reset condition, the user should read and then
Reset the MCUSR as early as possible in the program. If the register is cleared before another
reset occurs, the source of the reset can be found by examining the Reset Flags.
• Bits 7:5 – Res: Reserved Bits
These bits are reserved bits in the ATmega329P/3290P and will always read as zero.
• Bit 4 – WDCE: Watchdog Change Enable
This bit must be set when the WDE bit is written to logic zero. Otherwise, the Watchdog will not
be disabled. Once written to one, hardware will clear this bit after four clock cycles. Refer to the
description of the WDE bit for a Watchdog disable procedure. This bit must also be set when
changing the prescaler bits.
Bit
0x35 (0x55)
Read/Write
Initial Value
Bit
(0x60)
Read/Write
Initial Value
R
7
–
0
7
–
R
0
R
6
–
0
R
6
–
0
See Section “10.4.1” on page 49.
R
5
–
0
R
5
–
0
WDCE
R/W
JTRF
R/W
4
0
4
WDE
WDRF
R/W
R/W
3
0
3
See Bit Description
ATmega329P/3290P
WDP2
R/W
BORF
R/W
2
0
2
WDP1
R/W
EXTRF
1
0
R/W
1
WDP0
R/W
PORF
0
0
R/W
0
WDTCR
MCUSR
50