PIC16C711-20I/SO Microchip Technology, PIC16C711-20I/SO Datasheet - Page 63

• Manufacturer Part Number: PIC16C711-20I/SO
• Description: IC MCU OTP 1KX14 A/D 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C711-20I/SO

• Program Memory Type: OTP
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 18-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 13
• Ram Size: 68 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 68 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 1
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 8-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.5.1
External interrupt on RB0/INT pin is edge triggered:
either rising if bit INTEDG (OPTION<6>) is set, or fall-
ing, if the INTEDG bit is clear. When a valid edge
appears
(INTCON<1>) is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). Flag bit INTF
must be cleared in software in the interrupt service rou-
tine before re-enabling this interrupt. The INT interrupt
can wake-up the processor from SLEEP, if bit INTE was
set prior to going into SLEEP. The status of global inter-
rupt enable bit GIE decides whether or not the proces-
sor branches to the interrupt vector following wake-up.
See Section 8.8 for details on SLEEP mode.
FIGURE 8-19: INT PIN INTERRUPT TIMING
1997 Microchip Technology Inc.
INSTRUCTION FLOW
Note 1: INTF flag is sampled here (every Q1).
GIE bit
(INTCON<7>)
INTF flag
(INTCON<1>)
CLKOUT
INT pin
OSC1
Instruction
executed
Instruction
fetched
PC
2: Interrupt latency = 3-4 Tcy where Tcy = instruction cycle time.
3: CLKOUT is available only in RC oscillator mode.
4: For minimum width of INT pulse, refer to AC specs.
5: INTF is enabled to be set anytime during the Q4-Q1 cycles.
INT INTERRUPT
on
Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3
the
Q1
Inst (PC-1)
RB0/INT
Inst (PC)
1
Q2
PC
Q3
4
pin,
Q4
5
Q1
flag
Inst (PC+1)
Inst (PC)
Q2
1
bit
PC+1
Q3
INTF
Q4
Interrupt Latency
Q1
Dummy Cycle
Q2
8.5.2
An overflow (FFh
flag bit T0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit T0IE
(INTCON<5>). (Section 6.0)
8.5.3
An input change on PORTB<7:4> sets flag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>).
(Section 5.2)
PC+1
—
Note:
Q3
Q4
TMR0 INTERRUPT
PORTB INTCON CHANGE
2
For the PIC16C71
if a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RBIF inter-
rupt flag may not get set.
Q1
Dummy Cycle
Inst (0004h)
Q2
0004h
00h) in the TMR0 register will set
Q3
PIC16C71X
Q4
Q1
DS30272A-page 63
Inst (0005h)
Q2
Inst (0004h)
0005h
Q3
Q4