ATMEGA32U2-AU Atmel, ATMEGA32U2-AU Datasheet - Page 51

• Manufacturer Part Number: ATMEGA32U2-AU
• Description: IC MCU 8BIT 32KB FLASH 32TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32U2-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AVR MEGA
• No. Of I/o's: 22
• Eeprom Memory Size: 1KB
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

10.3
10.3.1
10.4
10.4.1
10.4.2
7799D–AVR–11/10
Internal Voltage Reference
Watchdog Timer
Voltage Reference Enable Signals and Start-up Time
Features
Overview
that remains enabled. This allows the device to stay attached to the bus during and after the
reset, while enhancing firmware reliability.
Figure 10-7. USB Reset During Operation
ATmega8U2/16U2/32U2 features an internal bandgap reference. This reference is used for
Brown-out Detection, and it can be used as an input to the Analog Comparator.
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
reference is not always turned on. The reference is on during the following situations:
Thus, when the BOD is not enabled, after setting the ACBG bit, the user must always allow the
reference to start up before the output from the Analog Comparator is used. To reduce power
consumption in Power-down mode, the user can avoid the three conditions above to ensure that
the reference is turned off before entering Power-down mode.
•
•
•
•
ATmega8U2/16U2/32U2 has an Enhanced Watchdog Timer (WDT). The WDT is a timer count-
ing cycles of a separate on-chip 128 kHz oscillator. The WDT gives a early warning interrupt
1. When the BOD is enabled (by programming the BODLEVEL [2..0] Fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
Clocked from separate On-chip Oscillator
3 Operating modes
Possible Hardware fuse Watchdog always on (WDTON) for fail-safe mode
Early warning after one Time-Out period reached, programmable Reset (see operating modes)
after 2 Time-Out periods reached.
– Interrupt
– System Reset
– Interrupt and System ResetSelectable Time-out period from 16ms to 8s
ACBG bit in ACSR).
DM
DP
CC
USB Traffic
“System and Reset Characteristics” on page
ATmega8U2/16U2/32U2
End of Reset
USB Traffic
267. To save power, the
51