PIC18F2525-E/SP Microchip Technology, PIC18F2525-E/SP Datasheet - Page 10
![IC MCU FLASH 24KX16 28-DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC18F2525-E/SP
Manufacturer Part Number
PIC18F2525-E/SP
Description
IC MCU FLASH 24KX16 28-DIP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F2221-ISO.pdf
(46 pages)
2.PIC18F2525-ISO.pdf
(412 pages)
3.PIC18F2525-ISO.pdf
(18 pages)
4.PIC18F2525-ISO.pdf
(18 pages)
5.PIC18F2525-ISO.pdf
(6 pages)
6.PIC18F2525-ISO.pdf
(6 pages)
Specifications of PIC18F2525-E/SP
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
48KB (24K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-DIP (0.300", 7.62mm)
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3986 B
Interface Type
SPI, I2C, EUSART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
25
Number Of Timers
1 x 8
Operating Supply Voltage
4.2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163022, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit
For Use With
I3DB18F4620 - BOARD DAUGHTER ICEPIC3DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F2525-E/SP
Manufacturer:
Microchip Technology
Quantity:
135
PIC18F2525/2620/4525/4620
24. Module: EUSART
25. Module: EUSART
26. Module: EUSART
27. Module: EUSART
DS80200D-page 10
The EUSART auto-baud feature may periodically
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CK pin for bit 0.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode, EUSART baud rates using
SPBRG values of ‘0’ and ‘1’ may not function
correctly.
Work around
Use another baud rate configuration to generate
the desired baud rate.
Date Codes that pertain to this issue:
All engineering and production devices.
During an auto-baud operation, the TX pin is tri-
stated. Transceivers which do not provide a pull-up
on the TX signal may cause the bus to become
inadvertently active and prevent additional bus
activity.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
28. Module: MSSP
29. Module: MSSP
30. Module: MSSP
In an I
unaddressed slave may respond to bus activity
when data on the bus matches its address. The
first occurrence will set the BF bit. The second
occurrence will set the BF and the SSPOV bits. In
both situations, the SSPIF bit is not set and an
interrupt will not occur. The device will vector to the
Interrupt Service Routine only if the interrupt is
enabled and an address match occurs.
Work around
The I
I
Date Codes that pertain to this issue:
All engineering and production devices.
In I
work correctly.
Work around
Use a BRG value greater than ‘0’ by setting
SSPADD ≥ ‘1’.
Date Codes that pertain to this issue:
All engineering and production devices.
In I
ware to begin data reception and cleared by the
peripheral after a byte is received. After a byte is
received, the device may take up to 80 T
RCEN and 800 T
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions typically
is long enough for the RCEN bit to clear. For mul-
tiple byte receptions, the software must wait until
the bit is cleared by the peripheral before the next
byte can be received.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C event to maintain normal operation.
2
2
C Master mode, the BRG value of ‘0’ may not
C Master mode, the RCEN bit is set by soft-
2
C slave must clear the SSPOV bit after each
2
C system with multiple slave nodes, an
CY
© 2006 Microchip Technology Inc.
during emulation.
CY
to clear