PIC24FJ64GB002-I/ML Microchip Technology, PIC24FJ64GB002-I/ML Datasheet - Page 197

• Manufacturer Part Number: PIC24FJ64GB002-I/ML
• Description: IC MCU 16BIT 64KB FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ64GB002-I/ML

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 19
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/IrDA/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9-ch x 10-bit
• Controller Family/series: PIC24
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: I2C, LIN, SPI, UART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

18.1
18.1.1
18.1.1.1
PIC24FJ64GB004 family devices have a built-in 1.5 kΩ
resistor on the D+ line that is available when the micro-
controller in operating in device mode. This is used to
signal an external Host that the device is operating in
Full-Speed Device mode. It is engaged by setting the
USBEN
(U1OTGCON<2>) is set, then the D+ pull-up is enabled
through the DPPULUP bit (U1OTGCON<7>).
Alternatively, an external resistor may be used on D+,
as shown in Figure 18-2.
FIGURE 18-2:
18.1.1.2
Many USB applications will likely have several different
sets of power requirements and configuration. The
most common power modes encountered are:
• Bus Power Only
• Self-Power Only
• Dual Power with Self-Power Dominance
Bus Power Only mode (Figure 18-3) is effectively the
simplest method. All power for the application is drawn
from the USB.
To meet the inrush current requirements of the USB 2.0
Specification, the total effective capacitance appearing
across V
In the USB Suspend mode, devices must consume no
more than 2.5 mA from the 5V V
cable. During the USB Suspend mode, the D+ or D-
pull-up resistor must remain active, which will consume
some of the allowed suspend current.
In Self-Power Only mode (Figure 18-4), the USB
application provides its own power, with very little
power being pulled from the USB. Note that an attach
indication is added to indicate when the USB has been
connected and the host is actively powering V
© 2009 Microchip Technology Inc.
PIC
BUS
Hardware Configuration
bit
®
DEVICE MODE
MCU
and ground must be no more than 10 μF.
D+ Pull-up Resistor
Power Modes
V
USB
(U1CON<0>).
D+
D-
EXTERNAL PULL-UP FOR
FULL-SPEED DEVICE
MODE
1.5 kΩ
If
BUS
Controller/HUB
the
line of the USB
Host
OTGEN
BUS
.
PIC24FJ64GB004 FAMILY
Preliminary
bit
To meet compliance specifications, the USB module
(and the D+ or D- pull-up resistor) should not be enabled
until the host actively drives V
tolerant I/O pins may be used for this purpose.
The application should never source any current onto
the 5V V
The Dual Power option with Self-Power Dominance
(Figure 18-5) allows the application to use internal
power primarily, but switch to power from the USB
when no internal power is available. Dual Power
devices must also meet all of the special requirements
for inrush current and Suspend mode current
previously described, and must not enable the USB
module until V
FIGURE 18-3:
FIGURE 18-4:
FIGURE 18-5:
V
V
~3.3V
V
V
~5V
~3.3V
BUS
~5V
SELF
BUS
SELF
V
~5V
BUS
100 kΩ
BUS
Regulator
Low I
Low I
100 kΩ
pin of the USB cable.
Q
BUS
Q
Regulator
0-100 kΩ
0-100 kΩ
3.3V
0-100 kΩ
is driven high.
3.3V
BUS POWER ONLY
SELF-POWER ONLY
DUAL POWER EXAMPLE
Attach Sense
BUS
Attach Sense
Attach Sense
high. One of the 5.5V
DS39940C-page 195
V
V
V
V
BUS
DD
USB
SS
V
V
V
V
V
V
V
V
BUS
DD
USB
SS
BUS
DD
USB
SS