ATMEGA168-15MZ Atmel, ATMEGA168-15MZ Datasheet - Page 30

• Manufacturer Part Number: ATMEGA168-15MZ
• Description: MCU AVR 16K FLASH 15MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA168-15MZ

• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 23
• Eeprom Size: 512 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Program Memory Size: 16KB (16K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: I²C, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: 2-Wire, SPI, USART, Serial
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 32QFN EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.5
6.6
30
Low Frequency Crystal Oscillator
Calibrated Internal RC Oscillator
ATmega48/88/168 Automotive
The device can utilize a 32.768 kHz watch crystal as clock source by a dedicated Low Fre-
quency Crystal Oscillator. The crystal should be connected as shown in
Oscillator is selected, start-up times are determined by the SUT Fuses and CKSEL0 as shown in
Table
Table 6-7.
Note:
The calibrated internal RC Oscillator by default provides a 8.0 MHz clock. The frequency is nom-
inal value at 3V and 25°C. The device is shipped with the CKDIV8 Fuse programmed. See
“System Clock Prescaler” on page 34
clock by programming the CKSEL Fuses as shown in
no external components. During reset, hardware loads the calibration byte into the OSCCAL
Register and thereby automatically calibrates the RC Oscillator. At 3V and 25°C, this calibration
gives a frequency of 8 MHz ± 1%. The tolerance of the internal RC oscillator remains better than
±10% within the whole automotive temperature and voltage ranges (2.7V to 5.5V, -40°C to
+125°C). The oscillator can be calibrated to any frequency in the range 7.3 - 8.1 MHz within ±1%
accuracy, by changing the OSCCAL register. When this Oscillator is used as the chip clock, the
Watchdog Oscillator will still be used for the Watchdog Timer and for the Reset Time-out. For
more information on the pre-programmed calibration value, see the section
page
Table 6-8.
Notes:
Power Conditions
BOD enabled
Fast rising power
Slowly rising power
BOD enabled
Fast rising power
Slowly rising power
282.
6-7.
1. These options should only be used if frequency stability at start-up is not important for the
1. The device is shipped with this option selected.
2. The frequency ranges are preliminary values. Actual values are TBD.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
application.
Fuse can be programmed in order to divide the internal frequency by 8.
Start-up Times for the Low Frequency Crystal Oscillator Clock Selection
Internal Calibrated RC Oscillator Operating Modes
Frequency Range
7.3 - 8.1
Start-up Time from
Power-down and
Reserved
Reserved
Power-save
(2)
32K CK
32K CK
32K CK
1K CK
1K CK
1K CK
(MHz)
for more details. This clock may be selected as the system
Additional Delay
14CK + 4.1 ms
14CK + 65 ms
14CK + 4.1 ms
Table
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
= 5.0V)
6-8. If selected, it will operate with
(1)
(1)(3)
(1)
(1)
CKSEL3..0
Figure
CKSEL0
0010
“Calibration Byte” on
CC
0
0
0
0
1
1
1
1
), the CKDIV8
6-2. When this
7530I–AVR–02/10
SUT1..0
00
01
10
11
00
01
10
11