PIC18LF2523-I/ML Microchip Technology, PIC18LF2523-I/ML Datasheet - Page 22
![IC PIC MCU FLASH 16KX16 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
PIC18LF2523-I/ML
Manufacturer Part Number
PIC18LF2523-I/ML
Description
IC PIC MCU FLASH 16KX16 28QFN
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F2221-ISO.pdf
(46 pages)
2.PIC18F2423-ISP.pdf
(54 pages)
3.PIC18F2423-ISP.pdf
(8 pages)
4.PIC18F2423-ISP.pdf
(34 pages)
Specifications of PIC18LF2523-I/ML
Core Size
8-Bit
Program Memory Size
32KB (16K x 16)
Core Processor
PIC
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
25
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
Controller Family/series
PIC18
No. Of I/o's
25
Eeprom Memory Size
256Byte
Ram Memory Size
1.5KB
Cpu Speed
40MHz
No. Of Timers
4
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PIC18F2XXX/4XXX FAMILY
3.4
The ID locations are programmed much like the code
memory. The ID registers are mapped in addresses,
200000h through 200007h. These locations read out
normally even after code protection.
TABLE 3-8:
DS39622L-page 22
Step 1: Direct access to code memory and enable writes.
Step 2: Load write buffer with 8 bytes and write.
Note:
Command
0000
0000
0000
0000
0000
0000
0000
0000
1101
1101
1101
1111
0000
4-Bit
ID Location Programming
The user only needs to fill the first 8 bytes
of the write buffer in order to write the ID
locations.
8E A6
9C A6
0E 20
6E F8
0E 00
6E F7
0E 00
6E F6
<MSB><LSB>
<MSB><LSB>
<MSB><LSB>
<MSB><LSB>
00 00
WRITE ID SEQUENCE
Data Payload
BSF
BCF
MOVLW 20h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 00h
MOVWF TBLPTRL
Write 2 bytes and post-increment address by 2.
Write 2 bytes and post-increment address by 2.
Write 2 bytes and post-increment address by 2.
Write 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
EECON1, EEPGD
EECON1, CFGS
Table 3-8
write the ID locations.
In order to modify the ID locations, refer to the method-
ology described in
Memory”. As with code memory, the ID locations must
be erased before being modified.
Core Instruction
demonstrates the code sequence required to
Section 3.2.1 “Modifying Code
2010 Microchip Technology Inc.