PIC18F2553-I/SP Microchip Technology, PIC18F2553-I/SP Datasheet - Page 43

• Manufacturer Part Number: PIC18F2553-I/SP
• Description: IC PIC MCU FLASH 16KX16 28SDIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2553-I/SP

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 24
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 2KB
• Cpu Speed: 48MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: MSSP, I2C, SPI, EUSART, CCP, ECCP
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM163025, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 5 V
• A/d Bit Size: 12 bit
• A/d Channels Available: 10
• Height: 3.3 mm
• Length: 34.67 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 7.24 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163025 - PIC DEM FULL SPEED USB DEMO BRD
• Lead Free Status / Rohs Status: Details

6.0
 2010 Microchip Technology Inc.
Standard Operating Conditions
Operating Temperature: 25C is recommended
Param
P11A
P12
P13
P14
P15
P16
P17
P18
Note 1:
No.
2:
3:
T
T
T
T
T
T
T
T
AC/DC CHARACTERISTICS TIMING REQUIREMENTS 
FOR PROGRAM/VERIFY TEST MODE (CONTINUED)
Sym
DRWT
HLD
SET
VALID
SET
DLY
HLD
HLD
Do not allow excess time when transitioning MCLR between V
executions to occur. The maximum transition time is:
where T
specific values, refer to the Electrical Characteristics section of the device data sheet for the particular device.
When ICPRT = 1, this specification also applies to ICV
At 0°C-50°C.
2 V
3 PGM Setup Time to MCLR/V
8 Delay Between Last PGC  and MCLR/V
2 Input Data Hold Time from MCLR/V
3 MCLR/V
4 MCLR/V
1 T
2 ms (for HS/PLL mode only) + 1.5 s (for EC mode only)
Data Write Polling Time
Data Out Valid from PGC 
CY
DD
CY
+ T
Setup Time to MCLR/V
is the instruction cycle time, T
PWRT
PP
PP
/RE3 to V
/RE3 to PGM 
(if enabled) + 1024 T
Characteristic
DD

PP
PP
/RE3 
PIC18F2XXX/4XXX FAMILY
/RE3 
OSC
PP
PWRT
/RE3 
(for LP, HS, HS/PLL and XT modes only) + 
PP
is the Power-up Timer period and T
/RE3 
PP
.
Min
100
10
—
4
2
2
0
0
IL
and V
Max
IHH
100
—
—
—
—
—
—
—
. This can cause spurious program
Units
ms
s
ns
ns
s
ns
OSC
s
s
is the oscillator period. For
(Note 2)
(Note 2)
Conditions
DS39622L-page 43