PIC18F4580-I/P Microchip Technology, PIC18F4580-I/P Datasheet - Page 23
![IC PIC MCU FLASH 16KX16 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC18F4580-I/P
Manufacturer Part Number
PIC18F4580-I/P
Description
IC PIC MCU FLASH 16KX16 40DIP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F2221-ISO.pdf
(46 pages)
3.PIC18F4480-IPT.pdf
(490 pages)
4.PIC18F4480-IPT.pdf
(8 pages)
5.PIC18F4480-IPT.pdf
(6 pages)
6.PIC18F4480-IPT.pdf
(6 pages)
7.PIC18F2580-ESO.pdf
(483 pages)
Specifications of PIC18F4580-I/P
Program Memory Type
FLASH
Program Memory Size
32KB (16K x 16)
Package / Case
40-DIP (0.600", 15.24mm)
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
36
Eeprom Size
256 x 8
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
1.5 KB
Interface Type
SPI/I2C/USART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
35
Number Of Timers
4
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
Minimum Operating Temperature
- 40 C
On-chip Adc
13-ch x 10-bit
Package
40PDIP
Device Core
PIC
Family Name
PIC18
Maximum Speed
40 MHz
Operating Supply Voltage
5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F4580-I/P
Manufacturer:
RENESAS
Quantity:
5 600
Part Number:
PIC18F4580-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC18F4580-I/PT
Manufacturer:
MICROCHIP
Quantity:
201
Company:
Part Number:
PIC18F4580-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC18F4580-I/PT
Manufacturer:
MICROCHI
Quantity:
20 000
3.5
The code sequence detailed in
used, except that the address used in “Step 2” will be in
the range of 000000h to 0007FFh.
TABLE 3-9:
FIGURE 3-8:
2010 Microchip Technology Inc.
Step 1: Enable writes and direct access to configuration memory.
Step 2: Set Table Pointer for configuration byte to be written. Write even/odd addresses.
Note 1:
Command
0000
0000
0000
0000
0000
0000
0000
0000
1111
0000
0000
0000
1111
0000
4-Bit
Boot Block Programming
Enabling the write protection of Configuration bits (WRTC = 0 in CONFIG6H) will prevent further writing of the
Configuration bits. Always write all the Configuration bits before enabling the write protection for Configuration bits.
8E A6
8C A6
0E 30
6E F8
0E 00
6E F7
0E 00
6E F6
<MSB ignored><LSB>
00 00
0E 01
6E F6
<MSB><LSB ignored>
00 00
SET ADDRESS POINTER TO CONFIGURATION LOCATION
CONFIGURATION PROGRAMMING FLOW
Data Payload
Delay P9 and P10
Time for Write
Configuration
Load Even
Program
Address
Done
Start
LSB
Table 3-5
BSF
BSF
MOVLW 30h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPRTH
MOVLW 00h
MOVWF TBLPTRL
Load 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
MOVLW 01h
MOVWF TBLPTRL
Load 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
should be
PIC18F2XXX/4XXX FAMILY
EECON1, EEPGD
EECON1, CFGS
3.6
Unlike code memory, the Configuration bits are
programmed a byte at a time. The Table Write, Begin
Programming 4-bit command (‘1111’) is used, but only
8 bits of the following 16-bit payload will be written. The
LSB of the payload will be written to even addresses and
the MSB will be written to odd addresses. The code
sequence to program two consecutive configuration
locations is shown in
Note:
Core Instruction
Configuration Bits Programming
Delay P9 and P10
The address must be explicitly written for
each byte programmed. The addresses
can not be incremented in this mode.
Time for Write
Configuration
Load Odd
(1)
Program
Address
Start
MSB
Done
Table
3-9.
DS39622L-page 23