PIC18F4580-I/P Microchip Technology, PIC18F4580-I/P Datasheet - Page 143

• Manufacturer Part Number: PIC18F4580-I/P
• Description: IC PIC MCU FLASH 16KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4580-I/P

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

11.4
PORTD is an 8-bit wide, bidirectional port. The corre-
sponding Data Direction register is TRISD. Setting a
TRISD bit (= 1) will make the corresponding PORTD
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISD bit (= 0)
will make the corresponding PORTD pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Output Latch register (LATD) is also memory
mapped. Read-modify-write operations on the LATD
register read and write the latched output value for
PORTD.
All pins on PORTD are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
Four of the PORTD pins are multiplexed with outputs
P1A, P1B, P1C and P1D of the Enhanced CCP
module. The operation of these additional PWM output
pins is covered in greater detail in Section 17.0
“Enhanced
Module”.
Four of the PORTD pins are multiplexed with the input
pins of the comparators. The operation of these input
pins is covered in greater detail in Section 21.0
“Comparator Module”.
© 2009 Microchip Technology Inc.
Note:
Note:
PORTD, TRISD and LATD
Registers
PORTD is only available on PIC18F4X80
devices.
On a Power-on Reset, these pins are
configured as analog inputs.
Capture/Compare/PWM
PIC18F2480/2580/4480/4580
(ECCP)
PORTD can also be configured as an 8-bit wide micro-
processor port (Parallel Slave Port) by setting control
bit, PSPMODE (TRISE<4>). In this mode, the input
buffers are TTL. See Section 11.6 “Parallel Slave
Port” for additional information on the Parallel Slave
Port (PSP).
EXAMPLE 11-4:
CLRF
CLRF
MOVLW
MOVWF
PORTD
LATD
0CFh
TRISD
; Initialize PORTD by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RD<3:0> as inputs
; RD<5:4> as outputs
; RD<7:6> as inputs
INITIALIZING PORTD
DS39637D-page 143