PIC18F8722-E/PT Microchip Technology, PIC18F8722-E/PT Datasheet - Page 45

• Manufacturer Part Number: PIC18F8722-E/PT
• Description: IC PIC MCU FLASH 64KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F8722-E/PT

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 70
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3936Byte
• Cpu Speed: 40MHz
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM183032, DM183022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164136 - DEVELOPMENT KIT FOR PIC18XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Lead Free Status / Rohs Status: Details

FIGURE 3-1:
FIGURE 3-2:
3.2.3
In RC_RUN mode, the CPU and peripherals are
clocked from the internal oscillator block using the
INTOSC multiplexer. In this mode, the primary clock is
shut down. When using the INTRC source, this mode
provides the best power conservation of all the Run
modes, while still executing code. It works well for user
applications which are not highly timing sensitive or do
not require high-speed clocks at all times.
If the primary clock source is the internal oscillator
block (either INTRC or INTOSC), there are no distin-
guishable
RC_RUN modes during execution. However, a clock
switch delay will occur during entry to and exit from
RC_RUN mode. Therefore, if the primary clock source
is the internal oscillator block, the use of RC_RUN
mode is not recommended.
 2004 Microchip Technology Inc.
Note 1: Clock transition typically occurs within 2-4 T
Peripheral
Program
Counter
T1OSI
OSC1
Note1: T
Clock
Clock
RC_RUN MODE
CPU Clock
CPU
PLL Clock
Peripheral
differences
Program
Counter
Output
2: Clock transition typically occurs within 2-4 T
T1OSI
OSC1
Clock
Q1
OST
SCS1:SCS0 bits Changed
Q2
= 1024 T
TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE
PC
TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)
Q3
between
Q4
OSC
; T
Q1
PLL
Q1
1
= 2 ms (approx). These intervals are not shown to scale.
T
PRI_RUN
OST
PC
(1)
2
Q2
Clock Transition
3
OSC
T
OSTS bit Set
Q3
PLL
and
Preliminary
.
OSC
(1)
.
(1)
PC + 2
n-1
Q4
This mode is entered by setting the SCS1 bit to ‘1’.
Although it is ignored, it is recommended that the SCS0
bit also be cleared; this is to maintain software compat-
ibility with future devices. When the clock source is
switched to the INTOSC multiplexer (see Figure 3-3),
the primary oscillator is shut down and the OSTS bit is
cleared. The IRCF bits may be modified at any time to
immediately change the clock speed.
n
Q1
PIC18F8722 FAMILY
1
Note:
Transition
2
Clock
n-1 n
(2)
Q2
Caution should be used when modifying a
single IRCF bit. If V
possible to select a higher clock speed
than is supported by the low V
Improper device operation may result if
the V
PC + 2
DD
Q3
/F
Q2
OSC
Q4
Q3 Q4
specifications are violated.
Q1
DD
Q1
PC + 4
Q2
is less than 3V, it is
PC + 4
Q2
DS39646B-page 43
Q3
Q3
DD
.