AT89C51RC2-3CSUM Atmel, AT89C51RC2-3CSUM Datasheet - Page 81

• Manufacturer Part Number: AT89C51RC2-3CSUM
• Description: IC 8051 MCU FLASH 32K 40DIP
• Manufacturer: Atmel
• Series: 89Cr

Specifications of AT89C51RC2-3CSUM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 60MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: SPI/UART
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT89
• Device Core: 80C51
• Device Core Size: 8b
• Frequency (max): 60MHz
• Total Internal Ram Size: 1.25KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-11 - KIT STARTER FOR AT89C51RX2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Warm Reset
Watchdog Reset
4180E–8051–10/06
Table 1. Minimum Reset Capacitor Value for a 50 kΩ Pull-down Resistor
Note:
To achieve a valid reset, the reset signal must be maintained for at least 2 machine
cycles (24 oscillator clock periods) while the oscillator is running. The number of clock
periods is mode independent (X2 or X1).
As detailed in Section “Hardware Watchdog Timer”, page 77, the WDT generates a 96-
clock period pulse on the RST pin. In order to properly propagate this pulse to the rest of
the application in case of external capacitor or power-supply supervisor circuit, a 1 kΩ
resistor must be added as shown Figure 33.
Figure 33. Reset Circuitry for WDT Reset-out Usage
Start-Up Time
Oscillator
20 ms
These values assume V
on/off sequences is too fast, the power-supply de-coupling capacitors may not be fully
discharged, leading to a bad reset sequence.
5 ms
VDD
VDD
VSS
+
RST
1K
820 nF
2.7 µF
1 ms
DD
RST
starts from 0V to the nominal value. If the time between 2
VDD
VSS
P
VDD Rise Time
10 ms
1.2 µF
3.9 µF
AT89C51RB2/RC2
From WDT
Reset Source
To CPU Core
and Peripherals
To Other
On-board
Circuitry
100 ms
(1)
12 µF
12 µF
81