ST7FLITE39M6TR STMicroelectronics, ST7FLITE39M6TR Datasheet - Page 132
![IC MCU 8BIT 8K FLASH 20SOIC](/photos/6/56/65691/497-20-soic__7_5mm_width__series_sml.jpg)
ST7FLITE39M6TR
Manufacturer Part Number
ST7FLITE39M6TR
Description
IC MCU 8BIT 8K FLASH 20SOIC
Manufacturer
STMicroelectronics
Series
ST7r
Specifications of ST7FLITE39M6TR
Core Processor
ST7
Core Size
8-Bit
Speed
16MHz
Connectivity
LINSCI, SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
15
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
384 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 7x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-SOIC (7.5mm Width)
Processor Series
ST7FLITE3x
Core
ST7
Data Bus Width
8 bit
Development Tools By Supplier
ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
For Use With
497-8403 - BOARD DEMO STCC08 AC SW DETECTOR497-6398 - BOARD EVAL ST7FLITE39/STM1403497-5858 - EVAL BOARD PLAYBACK ST7FLITE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST7FLITE39M6TR
Manufacturer:
IDT
Quantity:
2 799
Part Number:
ST7FLITE39M6TR
Manufacturer:
ST
Quantity:
20 000
ST7LITE3xF2
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
13.2.1 Voltage Characteristics
13.2.2 Current Characteristics
13.2.3 Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). Unused I/O pins must be tied in the same way to V
2. I
respected, the injection current must be limited externally to the I
while a negative injection is induced by V
corresponding V
3. All power (V
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. When several inputs are submitted to a current injection, the maximum ΣI
and negative injected currents (instantaneous values). These results are based on characterisation with ΣI
mum current injection on four I/O port pins of the device.
132/173
INJ(PIN)
I
INJ(PIN)
ΣI
V
V
Symbol
Symbol
Symbol
ESD(HBM)
DD
INJ(PIN)
T
I
I
V
VDD
VSS
must never be exceeded. This is implicitly insured if V
I
STG
T
IO
- V
IN
J
2) & 4)
DD
SS
2)
IN
) and ground (V
maximum must always be respected
Supply voltage
Input voltage on any pin
Electrostatic discharge voltage (Human Body Model)
Total current into V
Total current out of V
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB0 and PB1 pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
Storage temperature range
Maximum junction temperature (see
SS
) lines must always be connected to the external supply.
IN
<V
DD
SS
SS
. For true open-drain pads, there is no positive injection current, and the
power lines (source)
Ratings
Ratings
Ratings
ground lines (sink)
1) & 2)
DD
or V
5)
SS
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
section 14.2 on page
INJ(PIN)
5)
IN
maximum is respected. If V
3)
3)
value. A positive injection is induced by V
DD
or V
INJ(PIN)
5)
SS
according to their reset configuration.
see
160)
is the absolute sum of the positive
V
Maximum value
Maximum value
SS
section 13.7.3 on page 147
-0.3 to V
-65 to +150
Value
150
±20
7.0
-25
75
20
40
±5
±5
+5
±5
IN
DD
maximum cannot be
+0.3
INJ(PIN)
Unit
Unit
Unit
mA
°C
IN
V
maxi-
>V
DD