ST7FLITE29F1B6 STMicroelectronics, ST7FLITE29F1B6 Datasheet - Page 112
![IC MCU 8BIT 8K FLASH 20-DIP](/photos/6/89/68911/497-20-dip__300_mil__narrow_pdip_mdip__series_sml.jpg)
ST7FLITE29F1B6
Manufacturer Part Number
ST7FLITE29F1B6
Description
IC MCU 8BIT 8K FLASH 20-DIP
Manufacturer
STMicroelectronics
Series
ST7r
Specifications of ST7FLITE29F1B6
Core Processor
ST7
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
15
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
384 x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 5.5 V
Data Converters
A/D 7x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-DIP (0.300", 7.62mm)
Processor Series
ST7FLITE2x
Core
ST7
Data Bus Width
8 bit
Development Tools By Supplier
ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
For Use With
497-5858 - EVAL BOARD PLAYBACK ST7FLITE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ST7LITE2
CONTROL PIN CHARACTERISTICS (Cont’d)
Figure 84. RESET pin protection when LVD is enabled.
Figure 85. RESET pin protection when LVD is disabled.
Note 1:
Note 2: When the LVD is enabled, it is recommended not to connect a pull-up resistor or capacitor. A 10nF pull-down
capacitor is required to filter noise on the reset line.
Note 3: In case a capacitive power supply is used, it is recommended to connect a 1MΩ pull-down resistor to the RESET
pin to discharge any residual voltage induced by the capacitive effect of the power supply (this will add 5µA to the power
consumption of the MCU).
Note 4: Tips when using the LVD:
Note 5: Please refer to “Illegal Opcode Reset” on page 88 for more details on illegal opcode reset conditions.
112/133
EXTERNAL
Required
– The reset network protects the device against parasitic resets.
– The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the
– Whatever the reset source is (internal or external), the user must ensure that the level on the RESET pin can go
– Because the reset circuit is designed to allow the internal RESET to be output in the RESET pin, the user must en-
– 1. Check that all recommendations related to ICCCLK and reset circuit have been applied (see caution in
– 2. Check that the power supply is properly decoupled (100nF + 10µF close to the MCU). Refer to AN1709 and
– 3. The capacitors connected on the RESET pin and also the power supply are key to avoid any start-up marginality.
RESET
EXTERNAL
CIRCUIT
device can be damaged when the ST7 generates an internal reset (LVD or watchdog).
below the V
internally.
sure that the current sunk on the RESET pin is less than the absolute maximum value specified for I
section 13.2.2 on page
on page 7
AN2017. If this cannot be done, it is recommended to put a 100nF + 1MΩ pull-down on the RESET pin.
In most cases, steps 1 and 2 above are sufficient for a robust solution. Otherwise: replace 10nF pull-down on the
RESET pin with a 5µF to 20µF capacitor.”
RESET
USER
and notes above)
Required
IL
max. level specified in
0.01µF
0.01µF
92.
1MΩ
Optional
(note 3)
section 13.9.1 on page
V
V
DD
DD
R
R
ON
ON
Filter
Filter
111. Otherwise the reset will not be taken into account
1)2)3)4)
1)
GENERATOR
PULSE
GENERATOR
PULSE
WATCHDOG
ILLEGAL OPCODE
WATCHDOG
ILLEGAL OPCODE
LVD RESET
INTERNAL
RESET
INTERNAL
RESET
INJ(RESET)
ST72XXX
ST72XXX
Table 1
5)
5)
in