ST72F63BE6M1 STMicroelectronics, ST72F63BE6M1 Datasheet - Page 126

• Manufacturer Part Number: ST72F63BE6M1
• Description: IC MCU 8BIT 32K FLASH 24-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F63BE6M1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 14
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 24-SOIC (7.5mm Width)
• Data Converters: A/D 12x8b
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 14
• Number Of Timers: 1
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST72F63B-SK/RAIS, ST7MDTU3-EMU3, STX-RLINK
• Minimum Operating Temperature: 0 C
• For Use With: 497-5521 - EVAL BOARD LOW SPEED USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

On-chip peripherals
126/186
Figure 50. ADC block diagram
Digital A/D conversion result
The conversion is monotonic, meaning that the result never decreases if the analog input
does not and never increases if the analog input does not.
If the input voltage (V
the conversion result in the DR register is FFh (full scale) without overflow indication.
If input voltage (V
conversion result in the DR register is 00h.
The A/D converter is linear and the digital result of the conversion is stored in the ADCDR
register. The accuracy of the conversion is described in the parametric section.
R
is too high, this will result in a loss of accuracy due to leakage and sampling not being
completed in the allotted time.
A/D conversion phases
The A/D conversion is based on two conversion phases as shown in
●
●
While the ADC is on, these two phases are continuously repeated.
At the end of each conversion, the sample capacitor is kept loaded with the previous
measurement load. The advantage of this behavior is that it minimizes the current
consumption on the analog pin in case of single input channel measurement.
AIN
Sample capacitor loading [duration: t
During this phase, the V
sample capacitor.
A/D conversion [duration: t
During this phase, the A/D conversion is computed (8 successive approximations
cycles) and the C
the optimum analog to digital conversion accuracy.
is the maximum recommended impedance for an analog input signal. If the impedance
AIN0
AIN1
AINx
AIN
COCO
) is lower than or equal to V
AIN
ADC
ANALOG
) is greater than or equal to V
MUX
0
sample capacitor is disconnected from the analog input pin to get
ADON
AIN
4
Doc ID 7516 Rev 8
R
CONV
f
CPU
input voltage to be measured is loaded into the C
ADC
ADCDR
0
CH3
]
CH2
LOAD
D7
HOLD CONTROL
CH1
DIV 4
D6
]
SSA
CH0
C
ADC
D5
(low-level voltage reference) then the
DDA
ADCCSR
D4
(high-level voltage reference) then
ANALOG TO DIGITAL
D3
f
ADC
CONVERTER
D2
D1
Figure
D0
51:
ST7263Bxx
ADC