MC9S08SH16CTG Freescale Semiconductor, MC9S08SH16CTG Datasheet - Page 293

• Manufacturer Part Number: MC9S08SH16CTG
• Description: MCU 8BIT 16K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH16CTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
1
2
3
4
5
6
7
8
9
10
Num C
14
15
16
17
18
19
20
21
22
23
24
Typical values are measured at 25°C. Characterized, not tested
When IRQ or a pin interrupt is configured to detect rising edges, pulldown resistors are used in place of pullup resistors.
The specified resistor value is the actual value internal to the device. The pullup value may measure higher when measured
externally on the pin.
Power supply must maintain regulation within operating V
conditions. If positive injection current (V
in external power supply going out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or
if clock rate is very low (which would reduce overall power consumption).
All functional non-supply pins except RESET are internally clamped to V
named “PTA5/IRQ/TCLK/RESET.”
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
The RESET pin does not have a clamp diode to V
Maximum is highest voltage that POR is guaranteed.
Simulated, not tested.
Factory trimmed at V
D RAM retention voltage
D POR re-arm voltage
D POR re-arm time
P
P
P
P
P
P
P Bandgap Voltage Reference
T Low-voltage inhibit reset/recover
Low-voltage detection threshold —
high range
Low-voltage detection threshold —
low range
Low-voltage warning threshold —
high range 1
Low-voltage warning threshold —
high range 0
Low-voltage warning threshold
low range 1
Low-voltage warning threshold —
low range 0
hysteresis
Characteristic
DD
= 5.0 V, Temp = 25°C.
9
8
Table A-6. DC Characteristics (continued)
10
V
V
V
V
V
V
V
V
V
V
V
V
MC9S08SH32 Series Data Sheet, Rev. 2
DD
DD
DD
DD
DD
DD
In
DD
DD
DD
DD
DD
DD
> V
falling
falling
falling
falling
falling
falling
rising
rising
rising
rising
rising
rising
DD
) is greater than I
DD
Symbol
V
V
V
V
V
V
V
V
PRELIMINARY
t
V
V
. Do not drive this pin above V
POR
LVW3
LVW2
LVW1
LVW0
LVD1
LVD0
RAM
POR
hys
BG
DD
range during instantaneous and operating maximum current
DD
Condition
DD
, the injection current may flow out of V
5 V
3 V
load will shunt current greater than maximum injection
SS
and V
DD
DD
. In MC9S08SH32, the RESET pin is
.
2.48
2.54
2.84
2.90
2.66
2.72
1.18
Min
0.9
3.9
4.0
4.5
4.6
4.2
4.3
10
—
—
—
Appendix A Electrical Characteristics
1.202
Typ
2.56
2.62
2.92
2.98
2.74
2.80
100
0.6
1.4
4.0
4.1
4.6
4.7
4.3
4.4
60
—
1
DD
and could result
Max
2.64
2.70
3.00
3.06
2.82
2.88
1.21
1.0
2.0
4.1
4.2
4.7
4.8
4.4
4.5
—
—
—
Unit
mV
μs
V
V
V
V
V
V
V
V
V
293