MCF52210CAE66 Freescale Semiconductor, MCF52210CAE66 Datasheet - Page 38

• Manufacturer Part Number: MCF52210CAE66
• Description: IC MCU 64K FLASH 66MHZ 64LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF5221xr

Specifications of MCF52210CAE66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: I²C, SPI, UART/USART, USB OTG
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 43
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: MCF522x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/QSPI/UART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 43
• Number Of Timers: 18
• Operating Supply Voltage: - 0.3 V to + 4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M52210DEMO, M52211EVB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Package: 64LQFP
• Device Core: ColdFire
• Family Name: MCF5221x
• Maximum Speed: 66 MHz
• For Use With: M52210DEMO - BOARD DEV MCF5221X LOW COST
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.14
Figure 8
closed/open. When S1/S2 are closed & S3 is open, one input of the sample and hold circuit moves to (V
the other charges to the analog input voltage. When the switches are flipped, the charge on C1 and C2 are averaged via S3, with
the result that a single-ended analog input is switched to a differential voltage centered about (V
switch on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). There are additional
capacitances associated with the analog input pad, routing, etc., but these do not filter into the S/H output voltage, as S1 provides
isolation during the charge-sharing phase. One aspect of this circuit is that there is an on-going input current, which is a function
of the analog input voltage, V
Freescale Semiconductor
1
2
3
4
5
6
7
All measurements are preliminary pending full characterization, and made at V
INL measured from V
LSB = Least Significant Bit
INL measured from V
Includes power-up of ADC and V
ADC clock cycles
Current that can be injected or sourced from an unselected ADC signal input without impacting the performance of the ADC
SINAD
ENOB
Name
SFDR
THD
1.
2.
3.
4.
5.
shows the ADC input circuit during sample and hold. S1 and S2 are always open/closed at the same time that S3 is
Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8pF
Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04pF
Equivalent resistance for the channel select mux; 100 s
Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input and is only
connected to it at sampling time; 1.4pF
Equivalent input impedance, when the input is selected =
Analog Input
Equivalent Circuit for ADC Inputs
Total harmonic distortion
Spurious free dynamic range
Signal-to-noise plus distortion
Effective number of bits
1
IN
IN
= V
= 0.1V
REF
REFL
2
REFH
Characteristic
and the ADC clock frequency.
to V
REF
Figure 8. Equivalent Circuit for A/D Loading
to V
IN
Table 34. ADC Parameters
MCF52211 ColdFire Microcontroller, Rev. 2
= V
IN
REFH
= 0.9V
125W ESD Resistor
REFH
(V
REFH
3
- V
REFL
)/ 2
(ADC Clock Rate)  (1.410
8pF noise damping capacitor
S1
1
(continued)
S2
Min
9.1
—
—
—
1
DD
4
= 3.3V, V
S3
67 to 70.3
61 to 63.9
Typical
10.6
75
C2
C1
-12
REFH
)
REFH
S/H
= 3.3V, and V
Electrical Characteristics
-V
C1 = C2 = 1pF
Max
REFH
REFL
—
—
—
—
)/2. The switches
-V
REFL
REFL
)/2, while
Unit
= ground
Bits
dB
dB
dB
38