MC9S08QE128CLH Freescale Semiconductor, MC9S08QE128CLH Datasheet - Page 12

• Manufacturer Part Number: MC9S08QE128CLH
• Description: IC MCU 8BIT 128K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QE128CLH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 22x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08QE
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50.33 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMOQE128, EVBQE128
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 22-ch x 12-bit
• For Use With: EVBQE128 - BOARD EVAL FLEXIS QE128 FAMILYDEMOQE128 - DEMO BOARD FOR QE128 FLEXIS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical Characteristics
3
3.1
This section contains electrical and timing specifications for the MC9S08QE128 series of microcontrollers available at the time
of publication.
3.2
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better
understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate:
3.3
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the
limits specified in
conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised
that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this
high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for
instance, either V
12
C
D
P
T
Electrical Characteristics
Introduction
Parameter Classification
Absolute Maximum Ratings
1
2
Those parameters are guaranteed during production testing on each individual device.
Those parameters are achieved by the design characterization by measuring a statistically relevant sample
size across process variations.
Those parameters are achieved by design characterization on a small sample size from typical devices
under typical conditions unless otherwise noted. All values shown in the typical column are within this
category.
Those parameters are derived mainly from simulations.
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
SS
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins are internally clamped to V
The classification is shown in the column labeled “C” in the parameter tables where
appropriate.
Input must be current limited to the value specified. To determine the value of the required
Table 4
Single pin limit (applies to all port pins)
or V
DD
may affect device reliability or cause permanent damage to the device. For functional operating
) or the programmable pull-up resistor associated with the pin is enabled.
Rating
DD
MC9S08QE128 Series Data Sheet, Rev. 7
Table 4. Absolute Maximum Ratings
Table 3. Parameter Classifications
1, 2, 3
NOTE
Symbol
V
T
I
V
DD
I
DD
stg
D
SS
In
and V
DD
–0.3 to V
DD
) and negative (V
–0.3 to +3.8
.
–55 to 150
Value
± 25
120
DD
+ 0.3
Freescale Semiconductor
SS
) clamp
Unit
mA
mA
°C
V
V