MC908GT8CBE Freescale Semiconductor, MC908GT8CBE Datasheet - Page 54

• Manufacturer Part Number: MC908GT8CBE
• Description: IC MCU 8K FLASH 8MHZ 42-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GT8CBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 34
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Controller Family/series: HC08
• No. Of I/o's: 34
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GT
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Analog-to-Digital Converter (ADC)
3.6.5 ADC Voltage In (V
V
3.7 I/O Registers
These I/O registers control and monitor ADC operation:
3.7.1 ADC Status and Control Register
Function of the ADC status and control register (ADSCR) is described here.
COCO — Conversions Complete Bit
AIEN — ADC Interrupt Enable Bit
ADCO — ADC Continuous Conversion Bit
54
ADIN
•
•
•
In non-interrupt mode (AIEN = 0), COCO is a read-only bit that is set at the end of each conversion.
COCO will stay set until cleared by a read of the ADC data register. Reset clears this bit.
In interrupt mode (AIEN = 1), COCO is a read-only bit that is not set at the end of a conversion. It
always reads as a 0.
When this bit is set, an interrupt is generated at the end of an ADC conversion. The interrupt signal is
cleared when the data register is read or the status/control register is written. Reset clears the AIEN bit.
When set, the ADC will convert samples continuously and update the ADR register at the end of each
conversion. Only one conversion is completed between writes to the ADSCR when this bit is cleared.
Reset clears the ADCO bit.
1 = Conversion completed (AIEN = 0)
0 = Conversion not completed (AIEN = 0) or CPU interrupt enabled (AIEN = 1)
1 = ADC interrupt enabled
0 = ADC interrupt disabled
1 = Continuous ADC conversion
0 = One ADC conversion
is the input voltage signal from one of the eight ADC channels to the ADC module.
ADC status and control register (ADSCR)
ADC data register (ADR)
ADC clock register (ADCLK)
Address:
The write function of the COCO bit is reserved. When writing to the ADSCR
register, always have a 0 in the COCO bit position.
Reset:
Read:
Write:
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
$003C
COCO
Figure 3-3. ADC Status and Control Register (ADSCR)
Bit 7
R
R
0
ADIN
= Reserved
AIEN
)
6
0
ADCO
5
0
NOTE
ADCH4
4
1
ADCH3
3
1
ADCH2
2
1
ADCH1
1
1
Freescale Semiconductor
ADCH0
Bit 0
1