MC908GZ16MFAE Freescale Semiconductor, MC908GZ16MFAE Datasheet - Page 115

• Manufacturer Part Number: MC908GZ16MFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ16MFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI, UART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

10.16 Exiting Stop Mode
These events restart the system clocks and load the program counter with the reset vector or with an
interrupt vector:
Upon exit from stop mode, the system clocks begin running after an oscillator stabilization delay. A 12-bit
stop recovery counter inhibits the system clocks for 4096 CGMXCLK cycles after the reset or external
interrupt.
The short stop recovery bit, SSREC, in the CONFIG1 register controls the oscillator stabilization delay
during stop recovery. Setting SSREC reduces stop recovery time from 4096 CGMXCLK cycles to 32
CGMXCLK cycles.
Freescale Semiconductor
•
•
•
•
•
External reset — A logic 0 on the RST pin resets the MCU and loads the program counter with the
contents of locations $FFFE and $FFFF.
External interrupt — A high-to-low transition on an external interrupt pin loads the program counter
with the contents of locations:
–
–
Low-voltage inhibit (LVI) reset — A power supply voltage below the LVI
MCU and loads the program counter with the contents of locations $FFFE and $FFFF.
Timebase module (TBM) interrupt — A TBM interrupt loads the program counter with the contents
of locations $FFDC and $FFDD when the timebase counter has rolled over. This allows the TBM
to generate a periodic wakeup from stop mode.
MSCAN08 interrupt — MSCAN08 bus activity can wake the MCU from CPU stop. However, until
the oscillator starts up and synchronization is achieved the MSCAN08 will not respond to incoming
data.
$FFFA and $FFFB; IRQ pin
$FFE0 and $FFE1; keyboard interrupt pins
Use the full stop recovery time (SSREC = 0) in applications that use an
external crystal.
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
NOTE
TRIPF
voltage resets the
Exiting Stop Mode
115