SC5554MVR132 Freescale Semiconductor, SC5554MVR132 Datasheet - Page 16

• Manufacturer Part Number: SC5554MVR132
• Description: MCU MPC5554 DP ONLY 416-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC55xx Qorivvar

Specifications of SC5554MVR132

• Core Processor: e200z6
• Core Size: 32-Bit
• Speed: 132MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 256
• Program Memory Size: 2MB (2M x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.35 V ~ 1.65 V
• Data Converters: A/D 40x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 416-PBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
| V
V
If standby operation is not required, connect V
Applies to CLKOUT, external bus pins, and Nexus pins.
Maximum average RMS DC current.
Figure 3
Average current measured on automotive benchmark.
Peak currents can be higher on specialized code.
High use current measured while running optimized SPE assembly code with all code and data 100% locked in cache
(0% miss rate) with all channels of the eMIOS and eTPU running autonomously, plus the eDMA transferring data continuously from
SRAM to SRAM. Higher currents are possible if an “idle” loop that crosses cache lines is run from cache. Write code that avoids this
condition.
Figure 3
Power requirements for the V
segments. Refer to
Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O
segment, and the voltage of the I/O segment. Refer to
total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment.
Absolute value of current, measured at V
Weak pullup/down inactive. Measured at V
Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8
to 12
V
Up to 0.6 V during power up and power down.
Electrical Characteristics
16
PP
SSA
DDA0
can drop to 3.0 V during read operations.
o
refers to both V
C, in the ambient temperature range of 50
– V
shows an illustration of the I
shows an illustration of the I
DDA1
| must be < 0.1 V.
Table 11
SSA0
and V
for values to calculate the power dissipation for a specific operation.
DD33
SSA1
supply depend on the frequency of operation, load of all I/O pins, and the voltages on the I/O
DD_STBY
DD_STBY
. | V
MPC5554 Microcontroller Data Sheet, Rev. 3.0
IL
SSA0
DDE
and V
values interpolated for these temperature values.
values interpolated for these temperature values.
STBY
– V
= 3.6 V and V
IH
o
SSA1
C to 125
.
to ground.
Table 10
| must be < 0.1 V.
o
C. Applies to pad types: pad_a and pad_ae.
DDEH
for values to calculate power dissipation for specific operation. The
= 5.25 V. Applies to pad types: pad_fc, pad_sh, and pad_mh.
Freescale Semiconductor
o
C