AT90S2333-8PC Atmel, AT90S2333-8PC Datasheet - Page 76
![IC MCU 2K FLSH 8MHZ A/D 28DIP](/photos/7/21/72189/453-28-dip_sml.jpg)
AT90S2333-8PC
Manufacturer Part Number
AT90S2333-8PC
Description
IC MCU 2K FLSH 8MHZ A/D 28DIP
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheet
1.AT90LS2333-4AC.pdf
(103 pages)
Specifications of AT90S2333-8PC
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
2KB (1K x 16)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Programming the EEPROM
The programming algorithm for the EEPROM data memory is as follows (refer to Programming the Flash for details on
Command, Address and Data loading):
1. A: Load Command ‘0001 0001’.
2. C: Load Address Low Byte ($00 - $7F/$FF).
3. D: Load Data Low Byte ($00 - $FF).
4. E: Write Data Low Byte.
Reading the EEPROM
The algorithm for reading the EEPROM memory is as follows (refer to Programming the Flash for details on Command and
Address loading):
1. A: Load Command ‘0000 0011’.
2. C: Load Address Low Byte ($00 - $7F/$FF).
3. Set OE to ‘0’, and BS to ‘0’. The EEPROM data byte can now be read at DATA.
4. Set OE to ‘1’.
Programming the Fuse Bits
The algorithm for programming the Fuse bits is as follows (refer to Programming the Flash for details on Command and
Data loading):
1. A: Load Command ‘0100 0000’.
2. D: Load Data Low Byte. Bit n = ‘0’ programs and bit n = ‘1’ erases the Fuse bit.
3. Give WR a
Programming the Lock Bits
The algorithm for programming the Lock bits is as follows (refer to Programming the Flash for details on Command and
Data loading):
1. A: Load Command ‘0010 0000’.
2. D: Load Data Low Byte. Bit n = ‘0’ programs the Lock bit.
3. E: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
Reading the Fuse and Lock Bits
The algorithm for reading the Fuse and Lock bits is as follows (refer to Programming the Flash for details on Command
loading):
1. A: Load Command ‘0000 0100’.
2. Set OE to ‘0’, and BS to ‘0’. The status of the Fuse bits can now be read at DATA (‘0’ means programmed).
76
Bit 5 = SPIEN Fuse bit
Bit 4 = BODLEVEL Fuse bit
Bit 3 = BODEN Fuse bit
Bit 2 = CKSEL2 Fuse bit
Bit 1 = CKSEL1 Fuse bit
Bit 0 = CKSEL0 Fuse bit
Bit 7-6 = ‘1’. These bits are reserved and should be left unprogrammed (‘1’).
the Fuse bits does not generate any activity on the RDY/BSY pin.
Bit 2 = Lock Bit2
Bit 1 = Lock Bit1
Bit 7-3,0 = ‘1’. These bits are reserved and should be left unprogrammed (‘1’).
AT90S/LS2333 and AT90S/LS4433
t
WLWH_PFB
wide negative pulse to execute the programming,
t
WLWH_PFB
is found in Table 33. Programming