ATTINY28L-4AC Atmel, ATTINY28L-4AC Datasheet
ATTINY28L-4AC
Specifications of ATTINY28L-4AC
Available stocks
Related parts for ATTINY28L-4AC
ATTINY28L-4AC Summary of contents
Page 1
... PDIP, 32-lead TQFP, and 32-pad MLF • Operating Voltages – 1.8V - 5.5V for the ATtiny28V CC – 2.7V - 5.5V for the ATtiny28L CC • Speed Grades – 1.2 MHz for the ATtiny28V – MHz For the ATtiny28L Pin Configurations PDIP RESET 1 28 PA0 PD0 2 27 PA1 PD1 ...
Page 2
... Description Block Diagram ATtiny28L/V 2 The ATtiny28 is a low-power CMOS 8-bit microcontroller based on the AVR RISC archi- tecture. By executing powerful instructions in a single clock cycle, the ATtiny28 achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed. The AVR core combines a rich instruction set with 32 general-purpose working registers ...
Page 3
... Input to the inverting oscillator amplifier and input to the internal clock operating circuit. Output from the inverting oscillator amplifier. Reset input. An external reset is generated by a low level on the RESET pin. Reset pulses longer than 50 ns will generate a reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset. ATtiny28L/V 3 ...
Page 4
... Some of the status flags are cleared by writing a logical “1” to them. Note that the CBI and SBI instructions will operate on all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers $00 to $1F only. ATtiny28L/V 4 Bit 6 ...
Page 5
... PC ← then PC ← then PC ← then PC ← then PC ← ⊕ then PC ← ⊕ then PC ← then PC ← then PC ← then PC ← then PC ← then PC ← then PC ← then PC ← then PC ← ATtiny28L/V Flags # Clocks Z,C,N,V,H 1 Z,C,N,V,H 1 Z,C,N,V,H 1 Z,C,N,V,H 1 Z,C,N,V,H 1 Z,C,N,V,H 1 ...
Page 6
... Set T in SREG CLT Clear T in SREG SEH Set Half-carry Flag in SREG CLH Clear Half-carry Flag in SREG NOP No Operation SLEEP Sleep WDR Watchdog Reset ATtiny28L/V 6 Operation Rd ← (Z) (Z) ← ← ← ← ← ← (Z) I/O(P,b) ← 1 I/O(P,b) ← 0 Rd(n+1) ← Rd(n), Rd(0) ← 0 Rd(n) ← ...
Page 7
... Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28P3 28-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 32M1-A 32-pad, 5x5x1.0 body, Lead Pitch 0.50mm, Quad Flat No-lead/Micro Lead Frame Package (QFN/MLF) 1062FS–AVR–07/06 Ordering Code Package ATtiny28L-4AC 32A ATtiny28L-4PC 28P3 ATtiny28L-4MC 32M1-A ATtiny28L-4AI 32A ...
Page 8
... This package conforms to JEDEC reference MS-026, Variation ABA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R ATtiny28L PIN 1 IDENTIFIER ...
Page 9
... Orchard Parkway San Jose, CA 95131 R 1062FS–AVR–07/06 D PIN PLACES 0º ~ 15º REF eB TITLE 28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual Inline Package (PDIP) ATtiny28L COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A – – 4.5724 A1 0.508 – D 34.544 – ...
Page 10
... Pin TOP VIEW Pin #1 Notch (0. BOTTOM VIEW Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2. 2325 Orchard Parkway San Jose, CA 95131 R ATtiny28L TITLE 32M1-A, 32-pad 1.0 mm Body, Lead Pitch 0.50 mm, 3.10 mm Exposed Pad, Micro Lead Frame Package (MLF) SIDE VIEW ...
Page 11
... Errata All revisions 1062FS–AVR–07/06 No known errata. ATtiny28L/V 11 ...
Page 12
... Datasheet Revision History Rev – 01/06G Rev – 01/06G Rev – 03/05F ATtiny28L/V 12 Please note that the referring page numbers in this section are referred to this docu- ment. The referring revision in this section are referring to the document revision. 1. Updated chapter layout. 2. Updated “Ordering Information” on page 7. ...
Page 13
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...