AT89C51-24JC Atmel, AT89C51-24JC Datasheet - Page 4
![IC MICRO CTRL 24MHZ 44PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
AT89C51-24JC
Manufacturer Part Number
AT89C51-24JC
Description
IC MICRO CTRL 24MHZ 44PLCC
Manufacturer
Atmel
Series
89Cr
Datasheet
1.AT89C51-24AC.pdf
(17 pages)
Specifications of AT89C51-24JC
Core Processor
8051
Core Size
8-Bit
Speed
24MHz
Connectivity
UART/USART
Number Of I /o
32
Program Memory Size
4KB (4K x 8)
Program Memory Type
FLASH
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
44-PLCC
Data Bus Width
8 bit
Data Ram Size
128 B
Maximum Clock Frequency
24 MHz
Number Of Programmable I/os
32
Number Of Timers
2
Operating Supply Voltage
0 V to 6.6 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
Peripherals
-
Lead Free Status / Rohs Status
No
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT89C51-24JC
Manufacturer:
ATMEL
Quantity:
8 766
Part Number:
AT89C51-24JC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
pulse is skipped during each access to external Data
Memory.
If desired, ALE operation can be disabled by setting bit 0 of
SFR location 8EH. With the bit set, ALE is active only dur-
ing a MOVX or MOVC instruction. Otherwise, the pin is
weakly pulled high. Setting the ALE-disable bit has no
effect if the microcontroller is in external execution mode.
PSEN
Program Store Enable is the read strobe to external pro-
gram memory.
When the AT89C51 is executing code from external pro-
gram memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during
each access to external data memory.
EA/VPP
External Access Enable. EA must be strapped to GND in
order to enable the device to fetch code from external pro-
gram memory locations starting at 0000H up to FFFFH.
Note, however, that if lock bit 1 is programmed, EA will be
internally latched on reset.
EA should be strapped to V
executions.
This pin also receives the 12-volt programming enable volt-
age (V
12-volt V
XTAL1
Input to the inverting oscillator amplifier and input to the
internal clock operating circuit.
XTAL2
Output from the inverting oscillator amplifier.
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier which can be configured for use as
an on-chip oscillator, as shown in Figure 1. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
Status of External Pins During Idle and Power-down Modes
4
Mode
Idle
Idle
Power-down
Power-down
PP
) during Flash programming, for parts that require
PP
.
Program Memory
Internal
External
Internal
External
AT89C51
C C
for internal program
ALE
1
1
0
0
PSEN
1
1
0
0
unconnected while XTAL1 is driven as shown in Figure 2.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maxi-
mum voltage high and low time specifications must be
observed.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-
chip peripherals remain active. The mode is invoked by
software. The content of the on-chip RAM and all the spe-
cial functions registers remain unchanged during this
mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
It should be noted that when idle is terminated by a hard
ware reset, the device normally resumes program execu-
tion, from where it left off, up to two machine cycles before
the internal reset algorithm takes control. On-chip hardware
inhibits access to internal RAM in this event, but access to
the port pins is not inhibited. To eliminate the possibility of
an unexpected write to a port pin when Idle is terminated by
reset, the instruction following the one that invokes Idle
should not be one that writes to a port pin or to external
memory.
Figure 1. Oscillator Connections
Note:
PORT0
Float
Data
Data
Float
C1, C2 = 30 pF 10 pF for Crystals
= 40 pF 10 pF for Ceramic Resonators
PORT1
C2
C1
Data
Data
Data
Data
Address
PORT2
Data
Data
Data
XTAL2
XTAL1
GND
PORT3
Data
Data
Data
Data