ATTINY11L-2PI Atmel, ATTINY11L-2PI Datasheet - Page 34

• Manufacturer Part Number: ATTINY11L-2PI
• Description: IC AVR MCU 1K 2MHZ LV IND 8-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY11L-2PI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 2MHz
• Peripherals: WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Ram Size: -
• Data Converters: -
• Connectivity: -
• Other names: ATTINY11L2PI

General Interrupt Flag
Register – GIFR
Timer/Counter Interrupt Mask
Register – TIMSK
34
ATtiny11/12
• Bit 7 - Res: Reserved Bit
This bit is a reserved bit in the ATtiny11/12 and always reads as zero.
• Bit 6 - INTF0: External Interrupt Flag0
When an edge on the INT0 pin triggers an interrupt request, the corresponding interrupt
flag, INTF0 becomes set (one). If the I-bit in SREG and the corresponding interrupt
enable bit, INT0 bit in GIMSK, are set (one), the MCU will jump to the interrupt vector.
The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be
cleared by writing a logical one to it. The flag is always cleared when INT0 is configured
as level interrupt.
• Bit 5 - PCIF: Pin Change Interrupt Flag
When an event on any input or I/O pin triggers an interrupt request, PCIF becomes set
(one). If the I-bit in SREG and the PCIE bit in GIMSK are set (one), the MCU will jump to
the interrupt vector at address $002. The flag is cleared when the interrupt routine is
executed. Alternatively, the flag can be cleared by writing a logical one to it.
• Bits 4..0 - Res: Reserved Bits
These bits are reserved bits in the ATtiny11/12 and always read as zero.
• Bit 7..2 - Res: Reserved Bits
These bits are reserved bits in the ATtiny11/12 and always read as zero.
• Bit 1 - TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt (at vector
$003) is executed if an overflow in Timer/Counter0 occurs, i.e., when the Overflow Flag
(Timer0) is set (one) in the Timer/Counter Interrupt Flag Register – TIFR.
• Bit 0 - Res: Reserved Bit
This bit is a reserved bit in the ATtiny11/12 and always reads as zero.
Bit
$3A
Read/Write
Initial Value
Bit
$39
Read/Write
Initial Value
R
7
0
-
R
7
0
-
INTF0
R/W
0
6
R
6
0
-
PCIF
R/W
5
0
R
5
0
-
R
4
0
-
R
4
0
-
R
3
0
-
R
3
0
-
R
2
0
-
R
2
0
-
TOIE0
R/W
R
1
0
1
0
-
1006F–AVR–06/07
R
R
0
0
0
0
-
-
TIMSK
GIFR