PIC16C925/CL Microchip Technology, PIC16C925/CL Datasheet - Page 43

• Manufacturer Part Number: PIC16C925/CL
• Description: IC MCU EPROM 4KX14 LCDDVR 68CLCC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C925/CL

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: EPROM
• Ram Size: 176 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 68-CLCC Window, 68-CERQUAD
• For Use With: AC164308 - MODULE SKT FOR PM3 68PLCCDVA16XL680 - ADAPTER DEVICE FOR MPLAB-ICEAC164024 - ADAPTER PICSTART PLUS 68PLCCAC164022 - MODULE SKT PROMATEII 68PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

5.0
The Timer0 module has the following features:
• 8-bit timer/counter
• Readable and writable
• 8-bit software programmable prescaler
• Internal or external clock select
• Interrupt-on-overflow from FFh to 00h
• Edge select for external clock
Figure 5-1 is a simplified block diagram of the Timer0
module.
Timer mode is selected by clearing bit T0CS
(OPTION<5>). In Timer mode, the Timer0 module will
increment every instruction cycle (without prescaler). If
the TMR0 register is written, the increment is inhibited
for the following two instruction cycles (Figure 5-2 and
Figure 5-3). The user can work around this by writing
an adjusted value to the TMR0 register.
Counter mode is selected by setting bit T0CS
(OPTION<5>). In Counter mode, Timer0 will increment
either on every rising, or falling edge of pin RA4/T0CKI.
The incrementing edge is determined by the Timer0
Source Edge Select bit T0SE (OPTION<4>). Clearing
FIGURE 5-1:
2001 Microchip Technology Inc.
RA4/T0CKI
pin
Note 1: T0CS, T0SE, PSA, PS2:PS0 (OPTION<5:0>).
TIMER0 MODULE
2: The prescaler is shared with the Watchdog Timer (refer to Figure 5-6 for detailed block diagram).
T0SE
F
OSC
TIMER0 BLOCK DIAGRAM
/4
T0CS
0
1
PS2, PS1, PS0
Programmable
Prescaler
3
Preliminary
PSA
1
0
bit T0SE selects the rising edge. Restrictions on the
external clock input are discussed in detail in
Section 5.2.
The prescaler is mutually exclusively shared between
the Timer0 module and the Watchdog Timer. The
prescaler assignment is controlled in software by con-
trol bit PSA (OPTION<3>). Clearing bit PSA will assign
the prescaler to the Timer0 module. The prescaler is
not readable or writable. When the prescaler is
assigned to the Timer0 module, prescale values of 1:2,
1:4,..., 1:256 are selectable. Section 5.3 details the
operation of the prescaler.
5.1
The TMR0 interrupt is generated when the TMR0 reg-
ister overflows from FFh to 00h. This overflow sets bit
TMR0IF (INTCON<2>). The interrupt can be masked
by clearing bit T0IE (INTCON<5>). Bit TMR0IF must be
cleared in software by the Timer0 module Interrupt Ser-
vice Routine before re-enabling this interrupt. The
TMR0 interrupt cannot awaken the processor from
SLEEP, since the timer is shut-off during SLEEP.
Figure 5-4 displays the Timer0 interrupt timing.
PSout
(2 cycle delay)
Sync with
Timer0 Interrupt
Internal
Clocks
PIC16C925/926
PSout
Data Bus
TMR0
8
DS39544A-page 41
Flag bit TMR0IF
Set Interrupt
on Overflow