PIC16LF819T-E/ML Microchip Technology, PIC16LF819T-E/ML Datasheet - Page 120
![IC PIC MCU FLASH 2KX14 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
PIC16LF819T-E/ML
Manufacturer Part Number
PIC16LF819T-E/ML
Description
IC PIC MCU FLASH 2KX14 28QFN
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Specifications of PIC16LF819T-E/ML
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
- Current page: 120 of 324
- Download datasheet (6Mb)
PIC18F2450/4450
11.3.3
The Timer1 oscillator circuit draws very little power
during operation. Due to the low-power nature of the
oscillator, it may also be sensitive to rapidly changing
signals in close proximity.
The oscillator circuit, shown in Figure 11-3, should be
located as close as possible to the microcontroller.
There should be no circuits passing within the oscillator
circuit boundaries other than V
If a high-speed circuit must be located near the oscilla-
tor (such as the CCP1 pin in Output Compare or PWM
mode, or the primary oscillator using the OSC2 pin), a
grounded guard ring around the oscillator circuit, as
shown in Figure 11-4, may be helpful when used on a
single-sided PCB or in addition to a ground plane.
FIGURE 11-4:
11.4
The TMR1 register pair (TMR1H:TMR1L) increments
from 0000h to FFFFh and rolls over to 0000h. The
Timer1 interrupt, if enabled, is generated on overflow
which is latched in interrupt flag bit, TMR1IF
(PIR1<0>). This interrupt can be enabled or disabled
by setting or clearing the Timer1 Interrupt Enable bit,
TMR1IE (PIE1<0>).
DS39760D-page 118
Note: Not drawn to scale.
Timer1 Interrupt
TIMER1 OSCILLATOR LAYOUT
CONSIDERATIONS
OSCILLATOR CIRCUIT
WITH GROUNDED
GUARD RING
SS
OSC1
RC0
V
V
OSC2
RC1
RC2
or V
DD
SS
DD
.
11.5
If the CCP module is configured in Compare mode
to
(CCP1M3:CCP1M0 = 1011), this signal will reset
Timer1. The trigger from CCP1 will also start an A/D
conversion if the A/D module is enabled (see
Section 13.3.4 “Special Event Trigger” for more
information).
The module must be configured as either a timer or a
synchronous counter to take advantage of this feature.
When used this way, the CCPRH:CCPRL register pair
effectively becomes a period register for Timer1.
If Timer1 is running in Asynchronous Counter mode,
this Reset operation may not work.
In the event that a write to Timer1 coincides with a
Special Event Trigger, the write operation will take
precedence.
11.6
Adding an external LP oscillator to Timer1 (such as the
one described in Section 11.3 “Timer1 Oscillator”)
gives users the option to include RTC functionality to
their applications. This is accomplished with an
inexpensive watch crystal to provide an accurate time
base and several lines of application code to calculate
the time. When operating in Sleep mode and using a
battery or supercapacitor as a power source, it can
completely eliminate the need for a separate RTC
device and battery backup.
The application code routine, RTCisr, shown in
Example 11-1, demonstrates a simple method to
increment a counter at one-second intervals using an
Interrupt Service Routine. Incrementing the TMR1
register pair to overflow triggers the interrupt and calls
the routine which increments the seconds counter by
one. Additional counters for minutes and hours are
incremented as the previous counter overflows.
Since the register pair is 16 bits wide, counting up to
overflow the register directly from a 32.768 kHz clock
would take 2 seconds. To force the overflow at the
required one-second intervals, it is necessary to
preload it. The simplest method is to set the MSb of
TMR1H with a BSF instruction. Note that the TMR1L
register is never preloaded or altered; doing so may
introduce cumulative error over many cycles.
For this method to be accurate, Timer1 must operate in
Asynchronous mode and the Timer1 overflow interrupt
must be enabled (PIE1<0> = 1) as shown in the
routine, RTCinit. The Timer1 oscillator must also be
enabled and running at all times.
Note:
generate
Resetting Timer1 Using the CCP
Special Event Trigger
Using Timer1 as a Real-Time
Clock
The Special Event Triggers from the CCP1
module will not set the TMR1IF interrupt
flag bit (PIR1<0>).
a
© 2008 Microchip Technology Inc.
Special
Event
Trigger
Related parts for PIC16LF819T-E/ML
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC16LF819-I/SO](/photos/6/76/67656/150-18-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 2KX14 EEPROM 18SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/SS](/photos/6/58/65895/150-20-ssop_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 2KX14 EEPROM 20SSOP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/ML](/photos/6/81/68120/150-28-qfn_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 2KX14 EEPROM 28QFN
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/SOTSL](/photos/6/76/67656/150-18-soic_tmb.jpg)
Part Number:
Description:
IC PIC MCU FLASH 2KX14 18SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/MLTSL](/photos/6/81/68120/150-28-qfn_tmb.jpg)
Part Number:
Description:
IC PIC MCU FLASH 2KX14 28QFN
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/SSTSL](/photos/6/58/65895/150-20-ssop_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,20PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/P](/photos/6/76/67657/18-dip_300mil__tmb.jpg)
Part Number:
Description:
IC MCU FLASH 2KX14 EEPROM 18DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/SOG](/photos/6/76/67656/150-18-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 2KX14 18SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF819-I/SSG](/photos/6/58/65895/150-20-ssop_tmb.jpg)
Part Number:
Description:
IC PIC MCU FLASH 2KX14 20SSOP
Manufacturer:
Microchip Technology
![PIC16LF819-I/PTSL](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,DIP,18PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF1827-I/ML](/photos/6/81/68120/150-28-qfn_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC16LF, 32MHZ, QFN-28
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF1827-I/MV](/photos/12/13/121305/c04-152_mv_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC16LF, 32MHZ, QFN-28
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF1827-I/P](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC16LF, 32MHZ, DIP-18
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF874A-I/PT](/photos/6/82/68251/c04-076_pt_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC16LF, 20MHZ, TQFP-44
Manufacturer:
Microchip Technology
Datasheet:
![PIC16LF1827-I/MQ](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
7 KB Flash, 384 Bytes RAM, 32 MHz Int. Osc, 16 I/0, Enhanced Mid Range Core, Nan
Manufacturer:
Microchip Technology