DSPIC30F2010-30I/SO Microchip Technology, DSPIC30F2010-30I/SO Datasheet - Page 56

• Manufacturer Part Number: DSPIC30F2010-30I/SO
• Description: IC DSPIC MCU/DSP 12K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

dsPIC30F2010
8.2
The use of the ADPCFG and TRIS registers control the
operation of the A/D port pins. The port pins that are
desired as analog inputs must have their correspond-
ing TRIS bit set (input). If the TRIS bit is cleared (out-
put), the digital output level (V
converted.
When reading the PORT register, all pins configured as
analog input channel will read as cleared (a low level).
Pins configured as digital inputs will not convert an
analog input. Analog levels on any pin that is defined as
a digital input (including the ANx pins), may cause the
input buffer to consume current that exceeds the
device specifications.
8.2.1
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically this instruction
would be a NOP.
EXAMPLE 8-1:
DS70118H-page 56
MOV 0xFF00, W0 ; Configure PORTB<15:8>
MOV W0, TRISBB ; and PORTB<7:0> as outputs
NOP
btssPORTB, #13 ; Next Instruction
Configuring Analog Port Pins
I/O PORT WRITE/READ TIMING
; as inputs
; Delay 1 cycle
PORT WRITE/READ
EXAMPLE
OH
or V
OL
) will be
8.3
The Input Change Notification module provides the
dsPIC30F devices the ability to generate interrupt
requests to the processor in response to a
change-of-state on selected input pins. This module is
capable of detecting input change-of-states even in
Sleep mode, when the clocks are disabled. There are
up to 22 external signals (CN0 through CN21) that may
be selected (enabled) for generating an interrupt
request on a change-of-state.
Input Change Notification Module
© 2008 Microchip Technology Inc.