AT89C5131-TISIL Atmel, AT89C5131-TISIL Datasheet - Page 65
AT89C5131-TISIL
Manufacturer Part Number
AT89C5131-TISIL
Description
IC 8051 MCU FLASH 32K USB 28SOIC
Manufacturer
Atmel
Series
AT89C513xr
Datasheet
1.AT89C5131-S3SIL.pdf
(176 pages)
Specifications of AT89C5131-TISIL
Core Processor
C52X2
Core Size
8-Bit
Speed
48MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
LED, POR, PWM, WDT
Number Of I /o
18
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
For Use With
AT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Converters
-
- Current page: 65 of 176
- Download datasheet (3Mb)
Serial I/O Port
Framing Error Detection
4136B–USB–09/03
The serial I/O port in the AT89C5131 is compatible with the serial I/O port in the 80C52.
It provides both synchronous and asynchronous communication modes. It operates as
an Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex
modes (modes 1, 2 and 3). Asynchronous transmission and reception can occur simul-
taneously and at different baud rates.
Serial I/O port includes the following enhancements:
•
•
Framing bit error detection is provided for the three asynchronous modes (modes 1, 2
and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON regis-
ter (see Figure 31).
Figure 31. Framing Error Block Diagram
When this feature is enabled, the receiver checks each incoming data frame for a valid
stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous
transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in
SCON register (See Table 57) bit is set.
Software may examine FE bit after each reception to check for data errors. Once set,
only software or a reset can clear FE bit. Subsequently received frames with valid stop
bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the
last data bit (See Figure 32 and Figure 33).
Figure 32. UART Timings in Mode 1
Framing error detection
Automatic address recognition
SMOD0 = X
SMOD0 = 1
RXD
SM0/FE
FE
RI
SMOD1
SMOD0
SM1
Start
Bit
D0
SM2
-
D1
REN
Set FE Bit if Stop Bit is 0 (framing error) (SMOD0 = 1
SM0 to UART Mode Control (SMOD0 = 0)
POF
To UART Framing Error Control
D2
TB8
GF1
D3
Data Byte
RB8
GF0
D4
D5
PD
TI
D6
IDL
RI
D7
AT89C5131
SCON (98h)
PCON (87h)
Stop
Bit
65
Related parts for AT89C5131-TISIL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit Flash Microcontroller With Full Speed Usb Device At89c5131
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 52PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller with Full Speed USB Device
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
KIT STARTER FOR AT89C5131
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 48QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K USB 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: