TS87C52X2-VIA Atmel, TS87C52X2-VIA Datasheet - Page 32
![IC MCU 8BIT 8K OTP 40MHZ 40-DIP](/photos/6/70/67049/453-40-dip_sml.jpg)
TS87C52X2-VIA
Manufacturer Part Number
TS87C52X2-VIA
Description
IC MCU 8BIT 8K OTP 40MHZ 40-DIP
Manufacturer
Atmel
Series
87Cr
Datasheet
1.TS87C52X2-VCA.pdf
(55 pages)
Specifications of TS87C52X2-VIA
Core Processor
8051
Core Size
8-Bit
Speed
60/30MHz
Connectivity
UART/USART
Peripherals
POR
Number Of I /o
32
Program Memory Size
8KB (8K x 8)
Program Memory Type
OTP
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
EPROM Structure
EPROM Lock System
Encryption Array
Program Lock Bits
Signature Bytes
EPROM Programming
Set-up modes
32
TS8xCx2X2
The TS87C52X2 is divided in two different arrays:
•
•
In addition a third non programmable array is implemented:
•
The program Lock system, when programmed, protects the on-chip program against
software piracy.
Within the EPROM array are 64 bytes of encryption array that are initially unpro-
grammed (all FF’s). Every time a byte is addressed during program verify, 6 address
lines are used to select a byte of the encryption array. This byte is then exclusive-
NOR’ed (XNOR) with the code byte, creating an encrypted verify byte. The algorithm,
with the encryption array in the unprogrammed state, will return the code in its original,
unmodified form.
When using the encryption array, one important factor needs to be considered. If a byte
has the value FFh, verifying the byte will produce the encryption byte value. If a large
block (>64 bytes) of code is left unprogrammed, a verification routine will display the
content of the encryption array. For this reason all the unused code bytes should be pro-
grammed with random values. This will ensure program protection.
The three lock bits, when programmed according to Table 1., will provide different level
of protection for the on-chip code and data.
U: unprogrammed
P: programmed
WARNING: Security level 2 and 3 should only be programmed after EPROM and Core
verification.
The TS80/87C52X2 contains 4 factory programmed signatures bytes. To read these
bytes, perform the process described in section 9.
In order to program and verify the EPROM or to read the signature bytes, the
TS87C52X2 is placed in specific set-up modes (See Figure 11.).
Security
level
the code array: 8 Kbytes
the encryption array: 64 bytes
the signature array: 4 bytes
1
2
3
4
Program Lock Bits
LB1
U
P
U
U
LB2
U
U
P
U
LB3
U
U
U
P
Protection Description
No program lock features enabled. Code verify will still be
encrypted by the encryption array if programmed. MOVC
instruction executed from external program memory returns non
encrypted data.
MOVC instruction executed from external program memory are
disabled from fetching code bytes from internal memory, EA is
sampled and latched on reset, and further programming of the
EPROM is disabled.
Same as 2, also verify is disabled.
Same as 3, also external execution is disabled.
4184G–8051–09/06