AT91SAM7S64-MU Atmel, AT91SAM7S64-MU Datasheet - Page 677
AT91SAM7S64-MU
Manufacturer Part Number
AT91SAM7S64-MU
Description
IC ARM7 MCU FLASH 64K 64QFN
Manufacturer
Atmel
Series
AT91SAMr
Specifications of AT91SAM7S64-MU
Core Processor
ARM7
Core Size
16/32-Bit
Speed
55MHz
Connectivity
I²C, SPI, SSC, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VQFN
For Use With
AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 677 of 779
- Download datasheet (11Mb)
40.13 AT91SAM7S128 Errata - Revision C Parts
40.13.1
40.13.1.1
40.13.2
40.13.2.1
40.13.2.2
6175K–ATARM–30-Aug-10
Embedded Flash Controller (EFC)
Parallel Input/Output Controller (PIO)
EFC: Embedded Flash Access Time 1
PIO: Electrical Characteristics on NRST and PA0-PA16 and PA21-31
PIO: Drive Low NRST, PA0-PA16 and PA21-PA31
Refer to
Note: AT91SAM7S128 Revision C chip ID is 0x270A 0742.
The embedded Flash maximum access time is 20 MHz (instead of 30 MHz) at zero Wait State
(FWS = 0).
The maximum operating frequency with one Wait State (FWS = 1) is 48.1 MHz (instead of
55 MHz). Above 48.1 MHz and up to 55 MHz, two Wait States (FWS = 2) are required.
Set the number of Wait States (FWS) according to the frequency requirements described in this
errata.
When NRST or PA0-PA16 or PA21-PA31 are set as digital inputs with pull-up enabled, the volt-
age of the I/O stabilizes at VPull-up.
Vpull-up
This condition causes a leakage through VDDIO. This leakage is 45 µA per pad in worst case at
3.3 V, and 25 µA at 1.8V.
I Leakage
It is recommended to use an external pull-up if needed.
When NRST or PA0-PA16 and or PA21-PA31 are set as digital inputs with pull-up enabled, driv-
ing the I/O with an output impedance higher than 500 ohms may not drive the I/O to a logical
zero.
Output impedance must be lower than 500 ohms.
VPull-up Min
VDDIO - 0.65 V
Parameter
I Leakage at 3,3V
I Leakage at 1.8V
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Section 40.1 “Marking” on page
VPull-up Max
VDDIO - 0.45 V
Typ
2.5
1
µA
µA
Max
45
25
AT91SAM7S Series Preliminary
µA
µA
591.
677
Related parts for AT91SAM7S64-MU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVAL FOR ARM AT91SAM7S
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools KICKSTART KIT ATMEL AT91SAM7S
Manufacturer:
IAR Systems
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: