P89C662HBA/00,512 NXP Semiconductors, P89C662HBA/00,512 Datasheet - Page 12
![IC 80C51 MCU FLASH 32K 44-PLCC](/photos/6/98/69845/568-44-plcc_sot187-2_sml.jpg)
P89C662HBA/00,512
Manufacturer Part Number
P89C662HBA/00,512
Description
IC 80C51 MCU FLASH 32K 44-PLCC
Manufacturer
NXP Semiconductors
Series
89Cr
Datasheet
1.P89C660HBA00512.pdf
(89 pages)
Specifications of P89C662HBA/00,512
Core Processor
8051
Core Size
8-Bit
Speed
33MHz
Connectivity
I²C, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Other names
568-1269-5
935267444512
P89C662HBA
935267444512
P89C662HBA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89C662HBA/00,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
I
The I
8XC654, and 8XC652 devices.
Note that the P89C660/662/664/668 I
functions to port pins P1.6 and P1.7. Because of this, P1.6 and
P1.7 on these parts do not have a pull-up structure as found on the
80C51. Therefore P1.6 and P1.7 have open drain outputs on the
P89C660/662/664/668.
The I
between devices connected to the bus. The main features of the bus
are:
– Bidirectional data transfer between masters and slaves
– Multimaster bus (no central master)
– Arbitration between simultaneously transmitting masters without
– Serial clock synchronization allows devices with different bit rates
– Serial clock synchronization can be used as a handshake
– The I
The output latches of P1.6 and P1.7 must be set to logic 1 in order
to enable SIO1.
The P89C66x on-chip I
meets the I
(other than the low-speed mode) from and to the I
logic handles bytes transfer autonomously. It also keeps track of
serial transfers, and a status register (S1STA) reflects the status of
SIO1 and the I
The CPU interfaces to the I
function registers: S1CON (SIO1 control register), S1STA (SIO1
status register), S1DAT (SIO1 data register), and S1ADR (SIO1
slave address register). The SIO1 logic interfaces to the external I
bus via two port 1 pins: P1.6/SCL (serial clock line) and P1.7/SDA
(serial data line).
A typical I
how a data transfer is accomplished on the bus. Depending on the
state of the direction bit (R/W), two types of data transfers are
possible on the I
1. Data transfer from a master transmitter to a slave receiver. The
2. Data transfer from a slave transmitter to a master receiver. The
The master device generates all of the serial clock pulses and the
START and STOP conditions. A transfer is ended with a STOP
2002 Oct 28
2
C SERIAL COMMUNICATION — SIO1
corruption of serial data on the bus
to communicate via one serial bus
mechanism to suspend and resume serial transfer
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/1KB/2KB/8KB RAM
first byte transmitted by the master is the slave address. Next
follows a number of data bytes. The slave returns an
acknowledge bit after each received byte.
first byte (the slave address) is transmitted by the master. The
slave then returns an acknowledge bit. Next follows the data
bytes transmitted by the slave to the master. The master returns
an acknowledge bit after all received bytes other than the last
byte. At the end of the last received byte, a “not acknowledge” is
returned.
2
2
C serial port is identical to the I
C bus uses two wires (SDA and SCL) to transfer information
2
C bus may be used for test and diagnostic purposes
2
C bus configuration is shown in Figure 1. Figure 2 shows
2
C bus specification and supports all transfer modes
2
C bus.
2
C bus:
2
C logic provides a serial interface that
2
C logic via the following four special
2
C serial port on the 8XC554,
2
C pins are alternate
2
C bus. The SIO1
2
C
12
condition or with a repeated START condition. Since a repeated
START condition is also the beginning of the next serial transfer, the
I
Modes of Operation
The on-chip SIO1 logic may operate in the following four modes:
1. Master Transmitter mode:
2. Master Receiver Mode:
3. Slave Receiver mode:
4. Slave Transmitter mode:
In a given application, SIO1 may operate as a master and as a
slave. In the Slave mode, the SIO1 hardware looks for its own slave
address and the general call address. If one of these addresses is
detected, an interrupt is requested. When the microcontroller wishes
to become the bus master, the hardware waits until the bus is free
before the Master mode is entered so that a possible slave action is
not interrupted. If bus arbitration is lost in the Master mode, SIO1
switches to the Slave mode immediately and can detect its own
slave address in the same serial transfer.
2
C bus will not be released.
Serial data output through P1.7/SDA while P1.6/SCL outputs the
serial clock. The first transmitted byte contains the slave address
of the receiving device (7 bits) and the data direction bit. In this
mode the data direction bit (R/W) will be logic 0, and we say that
a “W” is transmitted. Thus the first byte transmitted is SLA+W.
Serial data is transmitted 8 bits at a time. After each byte is
transmitted, an acknowledge bit is received. START and STOP
conditions are output to indicate the beginning and the end of a
serial transfer.
The first transmitted byte contains the slave address of the
transmitting device (7 bits) and the data direction bit. In this
mode the data direction bit (R/W) will be logic 1, and we say that
an “R” is transmitted. Thus the first byte transmitted is SLA+R.
Serial data is received via P1.7/SDA while P1.6/SCL outputs the
serial clock. Serial data is received 8 bits at a time. After each
byte is received, an acknowledge bit is transmitted. START and
STOP conditions are output to indicate the beginning and end of
a serial transfer.
Serial data and the serial clock are received through P1.7/SDA
and P1.6/SCL. After each byte is received, an acknowledge bit is
transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is
performed by hardware after reception of the slave address and
direction bit.
The first byte is received and handled as in the Slave Receiver
mode. However, in this mode, the direction bit will indicate that
the transfer direction is reversed. Serial data is transmitted via
P1.7/SDA while the serial clock is input through P1.6/SCL.
START and STOP conditions are recognized as the beginning
and end of a serial transfer.
P89C660/P89C662/P89C664/
P89C668
Product data