LPC2294HBD144,551 NXP Semiconductors, LPC2294HBD144,551 Datasheet - Page 2

• Manufacturer Part Number: LPC2294HBD144,551
• Description: IC ARM7 MCU FLASH 256K 144-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2200r

Specifications of LPC2294HBD144,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, EBI/EMI, I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 112
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LQFP
• For Use With: OM10091 - KIT DEV PHYCORE-ARM7/LPC2220568-1757 - BOARD EVAL FOR LPC220X ARM MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 568-2383; 935278705551; LPC2294HBD144-S

NXP Semiconductors
3. Ordering information
LPC2292_2294_7
Product data sheet
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Table 1.
Type number
LPC2292FBD144
LPC2292FBD144/00
LPC2292FBD144/01
LPC2292FET144/00
LPC2292FET144/01
LPC2292FET144/G
16 kB on-chip static RAM and 256 kB on-chip flash program memory. 128-bit wide
interface/accelerator enables high-speed 60 MHz operation.
In-System Programming/In-Application Programming (ISP/IAP) via on-chip bootloader
software. Single flash sector or full chip erase in 400 ms and programming of 256 B in
1 ms.
EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the
on-chip RealMonitor software as well as high-speed real-time tracing of instruction
execution.
Two/four (LPC2292/LPC2294) interconnected CAN interfaces with advanced
acceptance filters. Additional serial interfaces include two UARTs (16C550), Fast
I
Eight channel 10-bit ADC with conversion time as low as 2.44 s.
Two 32-bit timers (with four capture and four compare channels), PWM unit (six
outputs), Real-Time Clock (RTC), and watchdog.
Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses.
Configurable external memory interface with up to four banks, each up to 16 MB and
8/16/32-bit data width.
Up to 112 general purpose I/O pins (5 V tolerant). Up to nine edge/level sensitive
external interrupt pins available.
60 MHz maximum CPU clock available from programmable on-chip PLL with settling
time of 100 s.
The on-chip crystal oscillator should have an operating range of 1 MHz to 25 MHz.
Power saving modes include Idle and Power-down.
Processor wake-up from Power-down mode via external interrupt.
Individual enable/disable of peripheral functions for power optimization.
Dual power supply:
2
N
N
C-bus (400 kbit/s) and two SPIs.
CPU operating voltage range of 1.65 V to 1.95 V (1.8 V
I/O power supply range of 3.0 V to 3.6 V (3.3 V
Ordering information
Rev. 7 — 4 December 2008
16/32-bit ARM microcontrollers with external memory interface
Package
Name
LQFP144
LQFP144
LQFP144
TFBGA144 plastic thin fine-pitch ball grid array package;
TFBGA144 plastic thin fine-pitch ball grid array package;
TFBGA144 plastic thin fine-pitch ball grid array package;
Description
plastic low profile quad flat package;
144 leads; body 20
plastic low profile quad flat package;
144 leads; body 20
plastic low profile quad flat package;
144 leads; body 20
144 balls; body 12
144 balls; body 12
144 balls; body 12
LPC2292/LPC2294
12
12
12
20
20
20
10 %) with 5 V tolerant I/O pads.
0.8 mm
0.8 mm
0.8 mm
1.4 mm
1.4 mm
1.4 mm
0.15 V).
© NXP B.V. 2008. All rights reserved.
Version
SOT486-1
SOT486-1
SOT486-1
SOT569-2
SOT569-2
SOT569-2
2 of 53