C8051F020 Silicon Laboratories Inc, C8051F020 Datasheet - Page 200
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F020
Manufacturer Part Number
C8051F020
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Specifications of C8051F020
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F020
Manufacturer:
SILICON
Quantity:
2
Company:
Part Number:
C8051F020
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F020
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Company:
Part Number:
C8051F020-GQ
Manufacturer:
SiliconL
Quantity:
4 035
Company:
Part Number:
C8051F020-GQ
Manufacturer:
MICRON
Quantity:
200
Company:
Part Number:
C8051F020-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F020-GQR
Manufacturer:
SILICON
Quantity:
3 000
Company:
Part Number:
C8051F020-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F020-GQR
Manufacturer:
SIL
Quantity:
20 000
Company:
Part Number:
C8051F020DK
Manufacturer:
SiliconL
Quantity:
10
Company:
Part Number:
C8051F020R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F020/1/2/3
Multiple masters may reside on the same bus. A Mode Fault flag (MODF, SPI0CN.5) is set to logic 1 when SPI0 is
configured as a master (MSTEN = 1) and its slave select signal NSS is pulled low. When the Mode Fault flag is set,
the MSTEN and SPIEN bits of the SPI control register are cleared by hardware, thereby placing the SPI0 module in
an "off-line" state. In a multiple-master environment, the system controller should check the state of the SLVSEL flag
(SPI0CN.2) to ensure the bus is free before setting the MSTEN bit and initiating a data transfer.
19.3. Serial Clock Timing
As shown in Figure 19.4, four combinations of serial clock phase and polarity can be selected using the clock control
bits in the SPI0 Configuration Register (SPI0CFG). The CKPHA bit (SPI0CFG.7) selects one of two clock phases
(edge used to latch the data). The CKPOL bit (SPI0CFG.6) selects between an active-high or active-low clock. Both
master and slave devices must be configured to use the same clock phase and polarity. Note: SPI0 should be disabled
(by clearing the SPIEN bit, SPI0CN.0) while changing the clock phase and polarity.
The SPI0 Clock Rate Register (SPI0CKR) as shown in Figure 19.7 controls the master mode serial clock frequency.
This register is ignored when operating in slave mode.
200
SCK
(CKPOL=0, CKPHA=0)
SCK
(CKPOL=0, CKPHA=1)
SCK
(CKPOL=1, CKPHA=0)
SCK
(CKPOL=1, CKPHA=1)
MISO/MOSI
NSS
MSB
Figure 19.4. Data/Clock Timing Diagram
Bit 6
Bit 5
Rev. 1.4
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0