LM358DR Rohm Semiconductor, LM358DR Datasheet - Page 7

• Manufacturer Part Number: LM358DR
• Description: IC OPAMP DUAL 32V 8-SOIC
• Manufacturer: Rohm Semiconductor
• Series: Trophyr

Specifications of LM358DR

• Slew Rate: 0.3 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Gain Bandwidth Product: 700kHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 3000µV
• Current - Supply: 1mA
• Current - Output / Channel: 30mA
• Voltage - Supply, Single/dual (±): 3 V ~ 32 V, ±1.5 V ~ 16 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: General Purpose
• No. Of Amplifiers: 2
• Bandwidth: 0.7MHz
• Supply Voltage Range: ± 1.5V To ± 16V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Operating Temperature Range: 0°C To
• Number Of Channels: 2
• Common Mode Rejection Ratio (min): 65 dB
• Input Offset Voltage: 7 mV
• Input Bias Current (max): 250 nA
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 450 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V, +/- 9 V
• Maximum Dual Supply Voltage: +/- 16 V
• Minimum Dual Supply Voltage: +/- 1.5 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 32 V
• Supply Voltage (min): 3 V
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: LM358DRTR

Derating Curves
1) Unused circuits
2) Input terminal voltage
3) Power supply (single / dual)
4) Power dissipation (Pd)
5) Short-circuits between pins and erroneous mounting
6) Operation in a strong electromagnetic field
7) Radiation
8) IC handing
9) IC operation
10) Board inspection
11) Output capacitor
Precautions
When there are unused circuits, it is recommended that they be connected as
in Figure 7, setting the non-inverting input terminal to a potential within the
in-phase input voltage range (VICR).
Applying GND + 32V to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, irrespective of
the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
The op-amp operates when the voltage is applied between Vcc and GND.
Therefore, the single supply op-amp can be used as a dual supply op-amp as well.
Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to the rise of chip temperature, including
reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under the actual operating conditions and apply a sufficient
margin in thermal design. Refer to the thermal derating curves for more information.
Incorrect mounting may damage the IC. In addition, the presence of foreign substances between the outputs, the output and the power supply, or the output
and GND may also result in IC destruction.
Operation in a strong electromagnetic field may cause malfunctions.
This IC is not designed to withstand radiation.
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo)
effects.
The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of Vcc and
GND, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output
terminal and GND and increasing the bias current for Class A operation will suppress crossover distortion.
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition,
when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please
take measures against ESD in the assembly process as well as during transportation and storage.
Discharge of the external output capacitor to Vcc is possible via internal parasitic elements when Vcc is shorted to GND, causing damage to the internal
circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage
comparators, use an output capacitor with a capacitance less than 0.1 F.
1000
800
600
400
200
0
25
Ambient temperature : Ta [ ]
LM358DR/PWR/DGKR
500[mV] TSSOP8 (*6)
470[mV] MSOP8/VSSOP8 (*7)
450[mV] SOIC8 (*8)
50
75
Power Dissipation
70[ ]
SOIC8 (*8)
TSSOP8 (*6)
MSOP8/VSSOP8 (*7)
ja = (Tj-Ta)/Pd[ /W]
100
Package
125
Fig.6 Derating Curves
150
7/8
Pd[W]
450
500
470
1000
LM2904DR/PWR/DGKR/VQDR/VQPWR
800
600
400
200
ja [ /W]
0
3.76
3.6
4.0
25
Ambient temperature : Ta [ ]
500[mV] TSSOP8 (*6)
470[mV] MSOP8/VSSOP8 (*7)
450[mV] SOIC8 (*8)
50
connect
to Vicm
75
TROPHY SERIES LM2904/2902/358/324 family
Fig.7 Disable circuit example
These Products are designed and produced by ROHM.
100
125
125[ ]
Vcc
GND
150