TS27L2IDT STMicroelectronics, TS27L2IDT Datasheet - Page 2

• Manufacturer Part Number: TS27L2IDT
• Description: IC AMP PREC LP DUAL OP 8 SOIC
• Manufacturer: STMicroelectronics

Specifications of TS27L2IDT

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Slew Rate: 0.04 V/µs
• Gain Bandwidth Product: 100kHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 1100µV
• Current - Supply: 10µA
• Current - Output / Channel: 45mA
• Voltage - Supply, Single/dual (±): 3 V ~ 16 V, ±1.5 V ~ 8 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Voltage Gain Db: 100 dB
• Common Mode Rejection Ratio (min): 65 dB
• Input Offset Voltage: 10 mV
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 0.03 mA
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Maximum Dual Supply Voltage: +/- 8 V
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2251-2

7100303-1
● This product is designed for the lighting of a Cold Cathode Fluorescent Lamp.
● Store this product under the conditions defined in the specification document.
● Do not store this product in an environment where dust, dirt or corrosive gas(salt,acid,base, etc.) is present.
● This product is subject to high voltage. If there is a possibility that the user may touch the product,
● This product is designed for use with general electronic equipment.
● Avoid using this product under high temperatures or high humidity or in an environment in which
● If the product does not have a built-in protective circuit (ci r cuit breaker, fuse, etc.),
● Use the product only within the specified input voltage, output power, output voltage
● Provide a measure for the prevention of surge voltage due to lightning, etc.
● To prevent problems arising from short-circuiting of the high-voltage section,
● This product is not designed to provide resistance to radiation.
● Ripples could be superimposed on the voltage and the current in the input source connected to the inverter ,
depending on the impedance in the input source, wiring, etc.
● This product uses thin wires. Observe the following precautions and handle it with care so
● Do not apply excessive stress during installation.
● Provide a clearance of 2 mm or more between the high-voltage section of this product and
When using this product, give due consideration to the precautionary notes described below and
ensure a safe design. Inappropriate use may result in electric shock, injury or fire.
● Please do not use the product, when dropping it, since there is a possibility of the parts damage.
● This product is subject to high voltage. Do not touch it while the power is on.
・Do not stack multiple products on top of one another.
・Do not allow the product to come in contact with tools, etc.
Do not use it with any other load.
provide a proper indication in order to draw the user's attention.
If it is to be used with medical equipment that directly affects human life or for the control of
transportation equipment to which passengers entrust thei r lives, provide thorough fail-safe measures.
dust, dirt or any corrosive gas (salt,acid,base, etc.) is present.
Also,be careful not to allow the formation of dew condensation. It may result in damage or electric shock.
it is recommended that a fuse be used at the input stage to prevent the generation of
smoke or fire in the event of a malfunction.
Even when the product has a built-in protective circuit (circuit breaker, fuse, etc.),
the circuit may not function properly due to inappropriate operating conditions or power-supply capacity.
It is recommended that an appropriate protective circuit (circuit breaker, fuse, etc.)
be provided separately from the built-in circuit.
and operating temperature ranges. Exceeding these values may result in damage, etc.
Abnormal voltage may result in damage, etc.
provide appropriate measures to prevent the entry of foreign substances following installation.
When you select an input source, please check waveforms, etc on the final set.
as not to cause wire breakage. Broken wire may result in damage, etc.
It may cause chipping and cracking,resulting in damage, etc.
the frame body on which the product is installed and also the conductor section (pattern , pad etc. ).
TDK CORPORATION
Failing to do so may result in electric shock.
Please confirm abnormality is not found in the product enough when using it by any chance.
Precautionary Notes Regarding the Use of This Inverter
No.
PRODUCT DRAWING
NAME OF DRAWING
MATERIALS NAME
Handling Precautions
Caution
Warning
DC-AC INVERTER UNIT CXA-P10A-P
PRODUCT NAME or MODEL,TITLE
QU
MATERIAL
DRAWING No.
CTR-0745-B
TSB-08-01-05(00)form-6(A4)
REMARK
PAGE
1