TS27L2IDT STMicroelectronics, TS27L2IDT Datasheet - Page 4

• Manufacturer Part Number: TS27L2IDT
• Description: IC AMP PREC LP DUAL OP 8 SOIC
• Manufacturer: STMicroelectronics

Specifications of TS27L2IDT

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Slew Rate: 0.04 V/µs
• Gain Bandwidth Product: 100kHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 1100µV
• Current - Supply: 10µA
• Current - Output / Channel: 45mA
• Voltage - Supply, Single/dual (±): 3 V ~ 16 V, ±1.5 V ~ 8 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Voltage Gain Db: 100 dB
• Common Mode Rejection Ratio (min): 65 dB
• Input Offset Voltage: 10 mV
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 0.03 mA
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Maximum Dual Supply Voltage: +/- 8 V
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2251-2

7100303-1
Note2.
Note3.
Note4.
Note5.
Note6.
Note7.
Note8.
Note1-1. Marking of TDK part No, Date code, Country of origin.
TDK CORPORATION
[2] Absolute maximum ratings
For circuit connection, prefer to test circ uit diagram [4].
For operation in floating mode, please remove the jumper(J1) on top side of PCB that pin2 and pin 5.
Please use minimum of 2mm clearance (all directions) between inverter high voltage area and any conductors.
Please refer to mechanical drawing for marking of high voltage area.
To prevent electrical discharge from high voltage area, please use non-conductive fastener in U mounting hole.
Open voltage (strike voltage) is measured across the transformer secondary winding at no load a s the reading at the
output connector would be less than the actual value.
If the start up voltage falls below Cold Cathode Tube strike voltage, the CCFL will not light up easily specially at lower
ambient temperature. Please review mounting instruction to avoid any abnormal operation due to coupling/leakage
capacitance of inverter high voltage area to any surrounding conductor.
For proper operation of circuit protection (fuse or ic protector), Please use minimu m of 5A capacity for input
power supply.
Operating Temp. range
Storage Temp. range
Humidity range
Output Power
Input Voltage
* : Conformity to RoHS Directive:This means that, in conformity with EU Directive 2002/95/EC,
1) TDK part No., Date code, Country of origin, is marked on the si de of transformer.
2) Date code example. (ex. APR. 2005)
3) Country of origin code example. (ex. JAPAN. CHINA).
lead, cadmium, hexavalent chromium, and specific bromi ne-based flame retardants, PBB
and PBDE, have not been used,except for exempted applications.
Items
5
Symbols
4
Pout
No.
Vin
RH
Ta
Ts
PRODUCT DRAWING
NAME OF DRAWING
MATERIALS NAME
Specification
R
-10~60
-20~85
0~6
95
Blank
One digit of production month. (Oct. : X , Nov. : Y, Dec. : Z).
Last digit of producti on year.
9
Product Conforming to RoHS Directive* Identification sign
DC-AC INVERTER UNIT CXA-P10A-P
PRODUCT NAME or MODEL,TITLE
%RH
VDC
Unit
°C
°C
W
QU
A maximum wet ball temperat ure is 38°C
MATERIAL
DRAWING No.
CTR-0745-B
TSB-08-01-05(00)form-6(A4)
Notes
REMARK
PAGE
3