HFA1110IBZ Intersil, HFA1110IBZ Datasheet - Page 3

• Manufacturer Part Number: HFA1110IBZ
• Description: IC BUFFER C-LOOP 750MHZ LD 8SOIC
• Manufacturer: Intersil

Specifications of HFA1110IBZ

• Amplifier Type: Buffer
• Number Of Circuits: 1
• Slew Rate: 1300 V/µs
• -3db Bandwidth: 750MHz
• Current - Input Bias: 10µA
• Voltage - Input Offset: 8000µV
• Current - Supply: 21mA
• Current - Output / Channel: 60mA
• Voltage - Supply, Single/dual (±): 9 V ~ 11 V, ±4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Gain Bandwidth: 750MHz
• Supply Voltage Range: ± 4.5V To ± 5.5V
• Output Current: 60mA
• Amplifier Output: Single Ended
• Operating Temperature Range: -40°C To +85°C
• Amplifier Case Style: SOIC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -

Electrical Specifications
NOTE:
Application Information
PC Board Layout
The frequency performance of this amplifier depends a great
deal on the amount of care taken in designing the PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
chip (0.1µF) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line will degrade the frequency response of the amplifier and
may cause oscillations. In most cases, the oscillation can be
avoided by placing a resistor (R
See the “Recommended R
specific recommendations.
An example of a good high frequency layout is the
Evaluation Board shown below.
Evaluation Board
An evaluation board is available for the HFA1110 (part
number HFA1110EVAL). Please contact your local sales
office for information.
The layout and schematic of the board are shown here:
NOTE: The SOIC version may be evaluated in the DIP board by
using a SOIC-to-DIP adapter such as Aries Electronics Part Number
08-350000-10.
-1dB Gain Compression
Reverse Gain (S
TRANSIENT RESPONSE
Rise Time
Overshoot (Note 2)
0.2% Settling Time (Note 2)
0.1% Settling Time (Note 2)
Overdrive Recovery Time
Differential Gain
Differential Phase
2. See Typical Performance Curves for more information.
PARAMETER
12
, Note 2)
S
vs Load Capacitance” graph for
3
S
V
) in series with the output.
SUPPLY
100MHz
100MHz, V
V
V
Rise/Fall = 1ns
V
V
3.58MHz, R
3.58MHz, R
OUT
OUT
OUT
OUT
= 0.5V Step
= 1.0V Step, Input Signal
= 1V to 0V
= 1V to 0V
= ±5V, R
TEST CONDITIONS
OUT
L
L
= 75Ω
= 75Ω
L
= 1V
= 100Ω, Unless Otherwise Specified (Continued)
P-P
HFA1110
TEMP (°C)
+5V
25
25
25
25
25
25
25
25
25
IN
0.1µF
10µF
MIN
50Ω
-
-
-
-
-
-
-
-
-
SCHEMATIC DIAGRAM
BOTTOM LAYOUT
1
2
3
4
TOP LAYOUT
0.025
TYP
0.04
HFA1110
-60
0.5
2.5
14
15
11
7
1
8
7
6
5
MAX
10µF
-
-
-
-
-
-
-
-
-
50Ω
R
S
UNITS
June 6, 2006
dBm
0.1µF
dB
ns
ns
ns
ns
%
%
°
FN2944.8
OUT
-5V