ICL7611DCPA Intersil, ICL7611DCPA Datasheet - Page 12

• Manufacturer Part Number: ICL7611DCPA
• Description: IC OPAMP 1.4MHZ CMOS LP 8-DIP
• Manufacturer: Intersil

Specifications of ICL7611DCPA

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Slew Rate: 1.6 V/µs
• Gain Bandwidth Product: 1.4MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 15000µV
• Current - Supply: 1mA
• Current - Output / Channel: 40mA
• Voltage - Supply, Single/dual (±): 2 V ~ 16 V, ±1 V ~ 8 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Bandwidth: 1.4 MHz
• Channel Separation: 120
• Common Mode Rejection Ratio: 96
• Current, Input Bias: 400 pA
• Current, Input Offset: 300 pA
• Current, Output: 40 mA
• Current, Supply: 0.01 mA
• Number Of Amplifiers: Single
• Package Type: PDIP-8
• Resistance, Input: 10^12 Ohms
• Temperature, Operating, Range: 0 to +70 °C
• Time, Rise: 2 μs
• Voltage, Gain: 75 dB
• Voltage, Input: -4.7 to 5.3 V
• Voltage, Noise: 100 nV/sqrt Hz
• Voltage, Offset: 20 mV
• Voltage, Output, High: +4.8 V
• Voltage, Output, Low: -4.8 V
• Voltage, Supply: 18 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Output Type: -
• -3db Bandwidth: -
• Other names: ICL7611DCPAIS

NOTES:
10. Controlling dimension: MILLIMETER. Converted inch dimensions
N
1
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
4. Dimension “E” does not include interlead flash or protrusions. Inter-
5. The chamfer on the body is optional. If it is not present, a visual index
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
Small Outline Plastic Packages (SOIC)
0.25(0.010)
Publication Number 95.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
lead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
feature must be located within the crosshatched area.
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
are not necessarily exact.
2
-A-
INDEX
AREA
3
e
B
D
M
C A
SEATING PLANE
M
-C-
E
-B-
B S
A
H
A1
12
α
0.10(0.004)
0.25(0.010)
M
L
h x 45°
B
M
ICL7611, ICL7612
C
M8.15
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
SYMBOL
A1
A
B
C
D
E
H
N
α
e
h
L
(JEDEC MS-012-AA ISSUE C)
0.0532
0.0040
0.013
0.0075
0.1890
0.1497
0.2284
0.0099
0.016
MIN
0°
0.050 BSC
INCHES
8
MAX
0.0688
0.0098
0.020
0.0098
0.1968
0.1574
0.2440
0.0196
0.050
8°
1.35
0.10
0.33
0.19
4.80
3.80
5.80
0.25
0.40
MILLIMETERS
MIN
0°
1.27 BSC
8
MAX
1.75
0.25
0.51
0.25
5.00
4.00
6.20
0.50
1.27
8°
Rev. 1 6/05
April 26, 2007
NOTES
FN2919.9
9
3
4
5
6
7
-
-
-
-
-
-