LMH6619MA/NOPB National Semiconductor, LMH6619MA/NOPB Datasheet - Page 21

• Manufacturer Part Number: LMH6619MA/NOPB
• Description: IC AMP DUAL RRIO 130MHZ 8-SOIC
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of LMH6619MA/NOPB

• Amplifier Type: Voltage Feedback
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 57 V/µs
• Gain Bandwidth Product: 58MHz
• -3db Bandwidth: 140MHz
• Current - Input Bias: 1.5µA
• Voltage - Input Offset: 100µV
• Current - Supply: 1.45mA
• Current - Output / Channel: 35mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 11 V, ±1.35 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Bandwidth: 130 MHz
• Common Mode Rejection Ratio: 96
• Current, Input Bias: 1 μA (NPN Active), -1.5 μA (PNP Active)
• Current, Input Offset: 0.01 μA
• Current, Output: ±35 mA
• Current, Supply: 1.3 mA
• Impedance, Thermal: 160 °C/W
• Number Of Amplifiers: Dual
• Package Type: SOIC-8
• Resistance, Input: 8 Megohms
• Temperature, Operating, Range: -40 to +125 °C
• Time, Fall: 30 ns
• Time, Rise: 30 ns
• Voltage, Gain: 100 dB
• Voltage, Input: 2.7 to 11 V
• Voltage, Noise: 10 nV/sqrt Hz
• Voltage, Offset: 0.1 mV
• Voltage, Output, High: 230 mV
• Voltage, Output, Low: 255 mV
• Voltage, Supply: 5 V
• Number Of Channels: 2
• Voltage Gain Db: 100 dB
• Common Mode Rejection Ratio (min): 81 dB
• Input Offset Voltage: 0.6 mV at 5 V
• Operating Supply Voltage: 3 V, 5 V, 9 V
• Supply Current: 3 mA at 5 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• For Use With: 551600075-001 - BOARD FOR SOIC LMH6612/19551600074-001 - BOARD FOR SOIC LMH6612/19
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LMH6619MA

When the op amp and the ADC are using the same supply, it
is important that both devices are well bypassed. A 0.1 µF
ceramic capacitor and a 10 µF tantalum capacitor should be
located as close as possible to each supply pin. A sample
SINGLE TO DIFFERENTIAL ADC DRIVER
Figure 5 shows the LMH6619 used to drive a differential ADC
with a single-ended input. The ADC121S625 is a fully differ-
FIGURE 4. LMH6618 and ADC121S101 Layout
FIGURE 5. LMH6619 Driving an ADC121S625
21
layout is shown in Figure 4. The 0.1 µF capacitors (C13 and
C6) and the 10 µF capacitors (C11 and C5) are located very
close to the supply pins of the LMH6618 and the
ADC121S101.
ential 12-bit ADC. Table 2 shows the performance data of the
LMH6619 and the ADC121S625.
20195840
www.national.com
20195880