AP7168-SPG-13 Diodes Inc, AP7168-SPG-13 Datasheet
![IC REG LDO ADJ 1.2A 8SOP](/photos/5/42/54225/sop-8l_sml.jpg)
AP7168-SPG-13
Specifications of AP7168-SPG-13
Available stocks
Related parts for AP7168-SPG-13
AP7168-SPG-13 Summary of contents
Page 1
... The typical quiescent current is approximately 125µA. Built-in current-limit and thermal-shutdown functions prevent IC from damage in fault conditions. The AP7168 is available in SO-8EP package. Features • Wide input voltage range: 2.2V – 5.5V • ...
Page 2
... T A AP7168 Document number: DS32019 Rev 1.2A LOW DROPOUT REGULATOR WITH POK Description IN Current Limit Gate EN and Thermal Driver Shutdown 0.8V 0.744V Parameter SO-8EP (Note 2, 4) Parameter www.diodes.com AP7168 OUT FB GND Ratings Unit 4 KV 300 0 Internal Limited -40 ~ 150 °C -65 ~150 °C 4 ...
Page 3
... OUT OUT V = 3.3V, V < 0.2V IN OUT 5.5V EN Force 2mA FB (or OUT for fixed version) rising V = 3.3V 1.2V IN OUT V = 5.5V POK SOP-8L-EP (Note www.diodes.com AP7168 Min Typ. Max ⎯ 125 180 -1 0.1 1 230 500 800 0.8 ⎯ 0. 0.02 -1.5 1.5 190 = 1.2V ...
Page 4
... Reference Voltage vs. Temperature 0.810 0.805 0.800 0.795 VIN=2.2V, Vout=1.0V VIN=3.3V, Vout=1.8V VIN=5.0V, Vout=3.3V 0.790 -50 -25 75.0 100.0 125 www.diodes.com AP7168 - 100 125 0 Tem perature ( C) Quiescent Current vs. I OUT =1.8V VIN=2.5V VIN=3.3V 0.2 0.4 0.6 0.8 1.0 1.2 ...
Page 5
... OUT -40 -45 -50 -55 -60 -65 -70 25°C -75 85°C -80 -40°C 100 0 www.diodes.com AP7168 Load Regulation =1.2V, OUT 25°C 85°C -40°C 0.4 0.8 1.2 I (A) OUT - Temperature ( C) PSRR 1000 10000 100000 Frequency (Hz) September 2010 ...
Page 6
... I OU 1A/us 500mA/div 50mA =0.1A) Start-up Time (V OUT V EN 2V/div V OUT 1V/div V POK 2V/div www.diodes.com AP7168 Time (500us/div) =3.3V) OUT C OUT =470uF (electrolytic) C OUT =10uF (Ceramic) C OUT =1uF (Ceramic) 1.2A 1A/us Time (100us/div) =1.2V, I =1.2A) OUT OUT C OUT =10uF Time (50us/div) September 2010 © ...
Page 7
... The output capacitor is required to stabilize and help the transient response of the LDO. The AP7168 is designed to have excellent transient response for most applications with a small amount of output capacitance. The AP7168 is stable for all available types and values of output capacitors ≥ 4.7μF. The device is also stable with multiple capacitors in parallel, which can be of any type of value ...
Page 8
... The device will remain stable and regulated in no load condition. ENABLE/SHUTDOWN Operation The AP7168 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin to keep the regulator output on at all time ...
Page 9
... Ordering Information Package SP : SO-8EP Package Device Code AP7168-SPG-13 SP Notes: 5. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. Marking Information SO-8EP Logo Part No. AP7168 Document number: DS32019 Rev 1.2A LOW DROPOUT REGULATOR WITH POK ...
Page 10
... Coplanarity applies to the exposed heat sink slug as well as the terminals. AP7168 Document number: DS32019 Rev 1.2A LOW DROPOUT REGULATOR WITH POK Exposed pad 45° 1 0.15/0.25 3.3Ref. Bottom View Gauge Plane Seating Plane 0.62/0.82 Detail "A" www.diodes.com AP7168 September 2010 © Diodes Incorporated ...
Page 11
... Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com AP7168 Document number: DS32019 Rev 1.2A LOW DROPOUT REGULATOR WITH POK IMPORTANT NOTICE LIFE SUPPORT www.diodes.com AP7168 September 2010 © Diodes Incorporated ...