LT3022EDHC#PBF Linear Technology, LT3022EDHC#PBF Datasheet - Page 5

• Manufacturer Part Number: LT3022EDHC#PBF
• Description: IC REG LDO ADJ 1A 16DFN
• Manufacturer: Linear Technology

Specifications of LT3022EDHC#PBF

• Regulator Topology: Positive Adjustable
• Voltage - Output: 0.2 ~ 9.5 V
• Voltage - Input: 0.9 ~ 10 V
• Voltage - Dropout (typical): 0.145V @ 1A
• Number Of Regulators: 1
• Current - Output: 1A
• Current - Limit (min): 1.1A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-WFDFN, Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Ripple Rejection (Note 13)
Current Limit (Note 9)
Input Reverse Leakage Current (Note 14)
Reverse Output Current (Notes 15, 16)
Minimum Required Output Current
ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifi cations are at T
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3022 regulator is tested and specifi ed under pulse load
conditions such that T
Performance of the LT3022E over the full –40°C and 125°C operating
junction temperature range is assured by design, characterization and
correlation with statistical process controls. The LT3022I regulators are
guaranteed over the full –40°C to 125°C operating junction temperature
range. High junction temperatures degrade operating lifetime. Operating
lifetime is derated at junction temperatures greater than 125°C.
Note 3: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specifi ed maximum operating junction
temperature may impair device reliability.
Note 4: Minimum input voltage is the voltage required by the LT3022 to
regulate the output voltage and supply the rated 1A output current. This
specifi cation is tested at V
minimum input voltage required for regulation equals the regulated output
voltage V
Note 5: Maximum junction temperature limits operating conditions. The
regulated output voltage specifi cation does not apply for all possible
combinations of input voltage and output current. Limit the output current
range if operating at maximum input voltage. Limit the input-to-output
voltage differential range if operating at maximum output current.
Note 6: The LT3022 typically supplies 1A output current with a 0.9V input
supply. The guaranteed minimum input voltage for 1A output current is
1.10V, especially if cold temperature operation is required.
OUT
plus the dropout voltage or 1.1V, whichever is greater.
J
≈ T
OUT
A
. The LT3022 is 100% tested at T
= 0.2V. For higher output voltages, the
LT3022
LT3022-1.2
LT3022-1.5
LT3022-1.8
V
V
V
LT3022
LT3022-1.2
LT3022-1.5
LT3022-1.8
V
IN
IN
IN
IN
= 10V, V
= V
= –10V, V
= 1.6V, V
A
OUT(NOMINAL)
A
= 25°C.
= 25°C.
OUT
OUT
OUT
V
f
V
f
V
f
V
f
V
V
V
V
The
RIPPLE
RIPPLE
RIPPLE
RIPPLE
IN
IN
IN
IN
OUT
OUT
OUT
OUT
= 0V
= 1.2V
= 0V
– V
– V
– V
– V
l
= 1.2V, V
= 1.2V, V
= 1.5V, V
= 1.8V, V
+ 0.5V, ΔV
OUT
OUT
OUT
OUT
denotes the specifi cations which apply over the full operating
= 120Hz, I
= 120Hz, I
= 120Hz, I
= 120Hz, I
= 1V, V
= 1V, V
= 1V, V
= 1V, V
Note 7: The LT3022 is tested and specifi ed for these conditions with ADJ
tied to OUT. Specifi cations for fi xed output voltage devices are referred to
the output voltage.
Note 8: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout the
output voltage equals: (V
Note 9: The LT3022 is tested and specifi ed for these conditions with
an external resistor divider (3.92k and 19.6k) setting V
external resistor divider adds 50μA of load current.
Note 10: GND pin current is tested with V
current source load. GND pin current increases in dropout. See GND pin
current curves in the Typical Performance Characteristics section.
Note 11: Adjust pin bias current fl ows out of the ADJ pin.
Note 12: Shutdown pin current fl ows into the SHDN pin.
Note 13: The LT3022 is tested and specifi ed for this condition with an
external resistor divider (3.92k and 5.9k) setting V
resistor divider adds 50μA of load current. The specifi cation refers to
the change in the 0.2V reference voltage, not the 0.5V output voltage.
Specifi cations for fi xed output voltage devices are referred to the output
voltage.
Note 14: Input reverse leakage current fl ows out of the IN pin.
Note 15: Reverse output current is tested with IN grounded and OUT
forced to the rated output voltage. This current fl ows into the OUT pin and
out of the GND pin.
Note 16: Reverse current is higher for the case of (rated_output)
< V
and is trying to restore the output voltage to its nominal value.
IN
IN
IN
IN
OUT
OUT
= 0V
= 0V
= 0V
= 0V
LOAD
LOAD
LOAD
LOAD
RIPPLE
RIPPLE
RIPPLE
RIPPLE
< V
≤ –5%
= 1A
= 1A
= 1A
= 1A
IN
= 0.5V
= 0.5V
= 0.5V
= 0.5V
, because the no-load recovery circuitry is active in this region
LT3022-1.5/LT3022-1.8
P-P
P-P
P-P
P-P
,
,
,
,
IN
LT3022/LT3022-1.2
l
l
– V
DROPOUT
1.1
55
51
51
51
1
).
IN
= V
2.6
1.7
0.1
0.1
0.1
0.1
70
66
66
66
4
OUT(NOMINAL)
OUT
to 0.5V. The external
OUT
20
5
5
5
5
to 1.2V. The
+ 0.4V and a
3022fa
5
mA
dB
dB
dB
dB
μA
μA
μA
μA
μA
A
A