TISP61089BDR Bourns Inc., TISP61089BDR Datasheet - Page 15

• Manufacturer Part Number: TISP61089BDR
• Description: SURGE SUPP SLIC PROG HV 8-SOP
• Manufacturer: Bourns Inc.

Specifications of TISP61089BDR

• Package / Case: 8-SOIC (3.9mm Width)
• Voltage - Breakover: *
• Voltage - Off State: 170V
• Current - Peak Pulse (10 X 1000µs): 30A
• Current - Hold (ih): 150mA
• Number Of Elements: 2
• Capacitance: 100pF
• Applications: SLIC
• Number Of Circuits: 2
• Voltage - Working: -100V
• Voltage - Clamping: -112V
• Technology: Mixed Technology
• Breakover Current Ibo Max: 6.5 A
• Rated Repetitive Off-state Voltage Vdrm: 170 V
• Off-state Leakage Current @ Vdrm Idrm: 0.005 mA
• Holding Current (ih Max): 150 mA
• Mounting Style: SMD/SMT
• Power (watts): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 6 shows the five tests used for this section. Columns 9 and 10 show the prospective currents for these tests using R
40 Ω. The two most stressful tests of this section are test 1 and test 2. As shown in Table 6, the peak currents for these tests are 2x17 A and
2x7.7 A respectively. With the exception of test 5, all the other tests require the series overcurrent protection to operate before the TISP61089B
current-time ratings are exceeded. In the case of test 2, with an R
cycle to prevent damage.
The test generator has a voltage source that can be varied from zero to 600 V rms and an output resistance of 20 Ω to each conductor. Table 4
shows the range of currents conducted by the TISP61089B.
Table 5 shows the nine tests used for this section. The TISP61089B will survive these peak current values as they are lower than the
TISP61089B current-time ratings.
NOTES: 1. If the equipment contains a voltage-limiting device or a current-limiting device, tests 1, 2 and 3 are repeated at a level just below
‘1089 Section 4.5.11 - Current-Limiting Protector Testing (Continued)
‘1089 Section 4.5.12 - First-Level Power Fault Testing
Test
‘1089 Section 4.5.13 - Second-Level Power Fault Testing for Central Office Equipment
AC Duration
#
1
2
3
4
5
6
7
8
9
900
s
TISP61089B High Voltage Ringing SLIC Protector
AC Duration
2. Test 5 uses a special circuit with transformer coupled a.c. and capacitive feed.
3. Tests 1 through 5 are requirements and the equipment shall not be damaged after these tests.
4. Tests 6 through 9 are desirable objectives and the equipment can be damaged after these tests.
the thresholds of the limiting devices.
900
900
0.5
30
s
1
1
5
2
1
Open-Circuit
RMS Voltage
0 to 600
V
RMS Voltage
Open-circuit
1000
1000
100
200
400
600
600
600
600
600
50
V
Short-Circuit
RMS Current
RMS Current
Short-circuit
0 to 30
Table 5. First-Level Power Fault Currents
A
0.33
0.17
0.33
0.67
1.00
0.09
0.5
2.2
3.0
A
1
5
Table 4. Wiring Simulator Testing
Tests
No
Transverse & Longitudinal
60
60
60
60
60
of
1
1
1
1
1
1
S
of 25 Ω, the overcurrent protection must operate within the initial a.c. half
Connections
Connections
Transverse &
Transverse &
Transverse &
Transverse &
Transverse &
Transverse &
Longitudinal
Longitudinal
Longitudinal
Longitudinal
Longitudinal
Longitudinal
Longitudinal
Longitudinal
Differential
Test
Test
Customers should verify actual device performance in their specific applications.
Primary
Fitted
Yes
Yes
No
No
No
No
No
No
No
Primary
Fitted
No
Resistance
Capacitive
Source
Specifications are subject to change without notice.
1000
1200
200
Resistance
150
600
600
273
200
Ω Ω Ω Ω
Source
20
Ω Ω Ω Ω
OCTOBER 2000 - REVISED JULY 2008
R
2x0.40
2x0.23
2x1.38
2x0.12
2x0.69
2x2.85
2x3.77
2x6.28
s
2x0.45
2x0.90
2x1.36
0 to 2x 19
R
= 25 Ω
TISP61089B I
s
S
TISP61089B I
= 25 Ω
A (peak)
values of 25 Ω and
A (peak)
R
2x0.37
2x1.30
2x0.12
2x5.89
s
2x0.22
2x0.44
2x0.89
2x1.33
2x0.68
2x2.71
2x3.54
0 to 2x 14
R
= 40 Ω Ω Ω Ω
s
TM
= 40 Ω Ω Ω Ω
TM