CN1206K20G EPCOS Inc, CN1206K20G Datasheet - Page 74
![VARISTOR 20VRMS 1206 SMD](/photos/1/40/14091/495-varistor_tvs_series_1206_sml.jpg)
CN1206K20G
Manufacturer Part Number
CN1206K20G
Description
VARISTOR 20VRMS 1206 SMD
Manufacturer
EPCOS Inc
Series
CN Standardr
Specifications of CN1206K20G
Varistor Voltage
33V
Current-surge
200A
Number Of Circuits
1
Maximum Ac Volts
20VAC
Maximum Dc Volts
26VDC
Energy
0.70J
Package / Case
1206 (3216 Metric)
Technology
Metal Oxide
Capacitance Value
600pF
Clamping Current
1A
Clamping Voltage
54V
Ac Voltage Rating (max)
20VAC
Dc Voltage Rating (max)
26VDC
Operating Temp Range
-55C to 125C
Mounting
Surface Mount
Surge Current (max)
200A
Size Code
1206
Product Length (mm)
3.2mm
Product Depth (mm)
1.6mm
Product Height (mm)
1.7mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
B72520V 200K 62
B72520V0200K062
B72520V200K62
B72520V0200K062
B72520V200K62
7.5
Thin or insufficient adhesive causes chips to loosen or become disconnected during curing.
Low viscosity of the adhesive causes chips to slip after mounting. It is advised to consult the
manufacturer of the adhesive on proper usage and amounts of adhesive to use.
7.6
Used flux should have less than or equal to 0.1 wt % of halogenated content, since flux residue
after soldering could lead to corrosion of the termination and/or increased leakage current on the
surface of the component. Strong acidic flux must not be used. The amount of flux applied should
be carefully controlled, since an excess may generate flux gas, which in turn is detrimental to sol-
derability.
7.7
Solderability is guaranteed for one year from date of delivery for multilayer varistors, CeraDiodes
and ESD/EMI filters (half a year for chips with AgPd and AgPt terminations) and two years for
SHCV and CU components, provided that components are stored in their original packages.
Storage temperature:
Relative humidity:
The solderability of the external electrodes may deteriorate if SMDs and leaded components are
stored where they are exposed to high humidity, dust or harmful gas (hydrogen chloride, sulfurous
acid gas or hydrogen sulfide).
Do not store SMDs and leaded components where they are exposed to heat or direct sunlight.
Otherwise the packing material may be deformed or SMDs/ leaded components may stick togeth-
er, causing problems during mounting.
After opening the factory seals, such as polyvinyl-sealed packages, it is recommended to use the
SMDs or leaded components as soon as possible.
7.8
Especially in the case of dual-wave soldering, it is of advantage to place the components on the
board before soldering in that way that their two terminals do not enter the solder bath at different
times.
Ideally, both terminals should be wetted simultaneously.
7.9
Please read Cautions and warnings and
Important notes at the end of this document.
Multilayer varistors (MLVs)
Standard series
An excessively long soldering time or high soldering temperature results in leaching of the outer
electrodes, causing poor adhesion and a change of electrical properties of the varistor due to
the loss of contact between electrodes and termination.
Wave soldering must not be applied for MLVs designated for reflow soldering only.
Keep the recommended down-cooling rate.
Adhesive application
Selection of flux
Storage of CTVSs
Placement of components on circuit board
Soldering cautions
75% annual average, 95% on 30 days a year
25 C to +45 C
Page 74 of 81