RR1220P-103-B-T5 Susumu, RR1220P-103-B-T5 Datasheet
![RES 10.0K OHM 1/10W .1% 0805 SMD](/photos/12/86/128631/rr_0402_series_sml.jpg)
RR1220P-103-B-T5
Specifications of RR1220P-103-B-T5
RR1220P103B
RR12P10.0KBTR
Available stocks
Related parts for RR1220P-103-B-T5
RR1220P-103-B-T5 Summary of contents
Page 1
...
Page 2
... Specification for Chip resistor RR1220 series a Code letter ③ b Nichrome alloy thin film Sn-Pb plating or Tin plating Polyimid resin coating Alumina ceramic SPEC.NO: SUSUMU CO.,LTD 2/14 (Unit )mm Dimension 2.0±0.2 1.25±0.2 0.4±0.1 0.4±0.2 0.4±0.2 Rev. No. RR00-1097 0 ...
Page 3
... Chip resistor RR1220 series Area of Recommended operation -55 70 125 Ambient temperature (V) (Ω) Rated resistance (W) Rated dissipation 100 V 200 V -55 to +125 deg C -55 to +125 deg C SPEC.NO: SUSUMU CO.,LTD 3/14 Fig.3 Derating curve deg C Rev. No. RR00-1097 0 ...
Page 4
... For other procedures, refer to IEC 60115-1, Sub-clause 4.13. Specification: Change in resistance : ±(0.5%+0.05Ω) Without damage by flash over (spark, arcing), burning or breakdown etc. TITLE: Specification for Chip resistor RR1220 series 5 to 35deg 85% 106kPa 20±2deg 70% 106kPa SPEC.NO: SUSUMU CO.,LTD RR00-1097 4/14 Rev. No. 0 ...
Page 5
... Chip resistor RR1220 series Measurement point A on metallic block ㎜ R 0.5 and Base material Insulating enclosure surface 100MΩ or more 1000MΩ or more ±(0.5%+0.05Ω) SPEC.NO: SUSUMU CO.,LTD 5/14 Insulating plate M easurement point etallic plate Specimen Presurization by spring Rev. No. RR00-1097 ...
Page 6
... Change in resistance : Without mechanical damage such as breaks. TITLE: Specification for Chip resistor RR1220 series Test state Pressurizing jig R230 Resistance meter ±(0.5%+0.05Ω) ±(0.5%+0.05Ω) SPEC.NO: SUSUMU CO.,LTD 6/ Loading Pressurizing jig R0.5 Specimen L 1/2 L Rev. No. ...
Page 7
... Without mechanical damage and distinct damage in appearance. TITLE: Specification for Chip resistor RR1220 series 30 s. 270±5deg C 10± sec. or less 220deg C over 60 s. max. 235±5deg C (Solder alloy: Sn-37Pb) 245±5deg C (Solder alloy: Sn-3Ag-0.5Cu) 2±0.5 s. SPEC.NO: SUSUMU CO.,LTD 7/14 Rev. No. RR00-1097 0 ...
Page 8
... Without mechanical damage such as breaks and distinct damage in appearance. Marking shall be legible. TITLE: Specification for Chip resistor RR1220 series 30 min 2∼3 min 30 min 2∼3 min ±(0.5%+0.05Ω) ±(0.5%+0.05Ω) ±(0.5%+0.05Ω) SPEC.NO: SUSUMU CO.,LTD 8/14 Rev. No. RR00-1097 0 ...
Page 9
...
Page 10
... It is soldered under the conditions of board surface temperature 240 to 250deg C(peak temperature) for upper-portion heated oven. TITLE: Specification for Chip resistor RR1220 series see Fig.4) see Fig.5) SPEC.NO: SUSUMU CO.,LTD 10/14 Rev. No. RR00-1097 0 ...
Page 11
... Country of origin ⑥ Shipping inspection code ⑦ Identification showing lead-free products. Example of the label RR1220P−102−B ③ Q.T.Y INSPECTED ④ SUSUMU CO.,LTD. N012501-- ⑥ C: ------------------------------------------------------------------- ⑦ ------------------------------------------------------------------- TITLE: Specification for Chip resistor RR1220 series 1000pcs r ...
Page 12
... Fig.7. Dimensions of reel TITLE: Specification for Chip resistor RR1220 series +0.1 φ1.5 Rectangular-hole 0 2.0±0.05 4.0±0.1 4.0±0.1 ※Pre-emptied holes : 75 holes(or 30 cm) or more. Unit : mm 105 Label ± 2 0.5 φ ± 21 0.8 0 φ 180 - 3 SPEC.NO: SUSUMU CO.,LTD 12/ ± 9 0.3 ± 13 1.4 Rev. No. RR00-1097 0 ...
Page 13
... It is necessary to protect the edge and protection coat of resistors from mechanical stress. (3) Handle with care when PC board is divided or fixed on support body, because bending of PC board after chip mounting will make mechanical stress for resistors. TITLE: Specification for Chip resistor RR1220 series −4 J. SPEC.NO: SUSUMU CO.,LTD RR00-1097 13/14 Rev. No. 0 ...
Page 14
... Using and Handling Refer to EIAJ RCR-2121 -- Electronic Industries Association of Japan technological report "Fixed resistor directions guideline.” TITLE: Specification for Chip resistor RR1220 series SPEC.NO: SUSUMU CO.,LTD RR00-1097 14/14 Rev. No. 0 ...