RR1220P-103-B-T5 Susumu, RR1220P-103-B-T5 Datasheet - Page 13
![RES 10.0K OHM 1/10W .1% 0805 SMD](/photos/12/86/128631/rr_0402_series_sml.jpg)
RR1220P-103-B-T5
Manufacturer Part Number
RR1220P-103-B-T5
Description
RES 10.0K OHM 1/10W .1% 0805 SMD
Manufacturer
Susumu
Series
RRr
Datasheet
1.RR1220P-3921-D-M.pdf
(14 pages)
Specifications of RR1220P-103-B-T5
Resistance (ohms)
10K
Power (watts)
0.1W, 1/10W
Composition
Thin Film
Temperature Coefficient
±25ppm/°C
Tolerance
±0.1%
Size / Dimension
0.079" L x 0.049" W (2.00mm x 1.25mm)
Height
0.016" (0.40mm)
Lead Style
Surface Mount (SMD - SMT)
Package / Case
0805 (2012 Metric)
Resistance In Ohms
10.0K
Case
0805 (2012 metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Other names
RR1220P-103-B
RR1220P103B
RR12P10.0KBTR
RR1220P103B
RR12P10.0KBTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
RR1220P-103-B-T5
Manufacturer:
MURATA
Quantity:
37 000
TITLE:
8. Precautions in use
8.1 Storage
(1) Resistor shall be stored in a room where temperature and humidity must be controlled.
(2) Resistor shall be stored as direct sunshine doesn't hit on it.
(3) Resistor shall be stored with no moisture, dust, a material that will make solderbility inferior, and a
(4) Resistor shall be stored with keeping the minimum package unit with uncivilized sealed (Keep the state
8.2 Time limit to storage
(1) The storage time limit of the product is reckoned on the day when the product was shipped by our
(2) Confirm solderbility beforehand when you use the one that the time limit was passed.
8.3 Chip mounting
(1) When chip are mounted on the PC board, the protection coat of resistors must not be scratched. If it will
(2) In case that resistor will be soldered by soldering iron, heating shall be done on the land, and soldering
(3) In case that resin coating or resin seal will be made for a PC board after chip mounting, do washing and
(4) According to shape, material, and pressure of clamping in chip mounting machine, there is the case that
(5) The glue to fix a resistor on the PC board around chip mounting, it is needed high insulation resistance
8.4 Using and Handling
(1) It is necessary to investigate the performance and reliability enough when using under harsh environment.
(2) It is necessary to protect the edge and protection coat of resistors from mechanical stress.
(3) Handle with care when PC board is divided or fixed on support body, because bending of PC board after
( temperature 5 to 35 deg C, humidity 45 to 85 % RH )
However, humidity keep it low, as it is possible.
harmful gas (hydrogen chloride, sulfurous acid gas, and hydrogen sulfide).
of the taping).
company and made within one year.
be scratched, it will make performance for moisture inferior.
iron must not hit on the resistor itself.
drying it enough before coating or sealing. If ion bear or moisture will be sealed in resin coating, it will
make performance for moisture inferior sometimes.
For resinous use, it is necessary to set up enough the curing conditions. As it get improper for the
condition, change of a resistance value are large and are a case.
crack will be appeared on resistor.
Control a shock energy for clamping resistor under 7×10
With a shock energy around clamping that says here, it is suited to a potential energy, in case that iron
block of 25g is dropped naturally to the resistor placed on iron plate for the height of 2.8mm.
and great performance or moisture. And it is needed that these characteristics are not inferior in using
temperature range and a hot spot temperature to be acting.
Especially, the performance of the product is occasionally damaged when using with the dewy state or
ion material adhered.
chip mounting will make mechanical stress for resistors.
Chip resistor RR1220 series
Specification for
SUSUMU
CO.,LTD
−4
SPEC.NO:
J.
RR00-1097
Rev. No.
13/14
0