PJRAS3X1S02 Switchcraft Inc., PJRAS3X1S02 Datasheet - Page 300

• Manufacturer Part Number: PJRAS3X1S02
• Description: PHONO JACK 3POS R/A GRN/BLU/RED
• Manufacturer: Switchcraft Inc.
• Series: PJRr

Specifications of PJRAS3X1S02

• Rohs Information: Switchcraft RoHS Info.
• Connector Type: Phono (RCA) Jack
• Gender: Female
• Signal Lines: Mono
• Plug/mating Plug Diameter: 3.20mm ID, 9.00mm OD (RCA)
• Number Of Positions/contacts: 3 Sets of 2 Conductors, 6 Contacts
• Internal Switch(s): Does Not Contain Switch
• Mounting Type: Through Hole, Right Angle
• Termination: Solder
• Shielding: Shielded
• Features: Grounding Tab
• Color: Blue, Green, Red
• Contact Plating: Nickel
• Contact Material: Copper Alloy
• Voltage Rating: 34 Volts
• Current Rating: 2 Amps
• Mounting Style: PCB
• Orientation: Right Angle
• Shell Plating: Steel
• Termination Style: Solder
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

FAX: 773 792 - 2129
SWITCHCRAFT, INC. 5555 N. Elston Ave. • Chicago, IL 60630
LEVER SWITCHES (continued)
LEVER-LITE
SERIES 84000 - ILLUMINATED LEVER SWITCHES
Lever-Lite
front-of-panel mounting, relamping, terminating, color
changes and removal. A minimum of time is required to install
singly, in rows, or in matrix arrays to meet a wide variety of
switching applications. 2- and 3-position types are available in
non-locking functions. Mounts on .875" (22.22 mm) horizontal
centers or 1.5" (38.1 mm) vertical centers. Talk-listen
(intercom) function is also available. Illumination technique
provides a different color for each lever position.
LAMPS
Standard T 1-3/4" midget flange-base lamps (not supplied)
are available in voltages up to 28V.
SPECIAL ORDER FEATURES
1. Talk-Listen (Intercom) function.
2. Welded cross bar gold alloy for dry circuit and silver
Remove escutcheon and lever
assembly. (see “MOUNTING” above)
For relamping, pull lamp out of
retainer with finger-tip. Replace lamp.
MOUNTING
Grasp fingernail slots on opposite sides
of escutcheon and snap out. Next, grasp
lever and pull lever assembly free. Insert
switch into panel hole.
RELAMPING/REPLACING
COLOR FILTERS
contacts are available. See page 294.
®
III illuminated lever switches are designed for
®
III
Turn two internal screws clockwise with
screwdriver to securely mount switch
to panel.
Lever-Lite III switches are designed for simplified lamp installation and replacement,
and color filter changes or custom installation in the field or on the OEM production
line. Lamps and filters may be changed at any time with ease and without
dismounting switch from panel or disturbing wiring.
For color filters, use fingernails or
small screwdriver to remove. Gently
lift (don’t pry) up under edge of
filter until it “pops” out.
DIMENSIONS ARE FOR REFERENCE ONLY
LEVER-LITE
LEVER-LITE
®
®
ILLUMINATION
A single internal lamp provides brilliant lever lighting in any
color required. Standard factory installed color filters are
provided as follows: Series 84000, Multi-Color Illumination
2-position - Amber (neutral position); green (down position).
(down position). One-color (all positions) and non-illuminated
switches can be specified on special order. Switchcraft will
install filters for non-standard illumination requirements at
nominal cost on special order.
3-position - Red (up position); amber (neutral position); green
ILLUMINATED LEVER SWITCHES – SERIES 84000
ILLUMINATED LEVER SWITCHES – SERIES 84000
(mm)
Inch
Replace lever assembly and “snap”
escutcheon into place. Installation
complete!
Place new filter in position and press
until it “snaps” in. Replace lever
assembly and escutcheon.
(see “MOUNTING” above)
SWITCHES
295