PJRAS3X1S02 Switchcraft Inc., PJRAS3X1S02 Datasheet - Page 85

• Manufacturer Part Number: PJRAS3X1S02
• Description: PHONO JACK 3POS R/A GRN/BLU/RED
• Manufacturer: Switchcraft Inc.
• Series: PJRr

Specifications of PJRAS3X1S02

• Rohs Information: Switchcraft RoHS Info.
• Connector Type: Phono (RCA) Jack
• Gender: Female
• Signal Lines: Mono
• Plug/mating Plug Diameter: 3.20mm ID, 9.00mm OD (RCA)
• Number Of Positions/contacts: 3 Sets of 2 Conductors, 6 Contacts
• Internal Switch(s): Does Not Contain Switch
• Mounting Type: Through Hole, Right Angle
• Termination: Solder
• Shielding: Shielded
• Features: Grounding Tab
• Color: Blue, Green, Red
• Contact Plating: Nickel
• Contact Material: Copper Alloy
• Voltage Rating: 34 Volts
• Current Rating: 2 Amps
• Mounting Style: PCB
• Orientation: Right Angle
• Shell Plating: Steel
• Termination Style: Solder
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

80
w w w . s w i t c h c r a f t . c o m
JACKS AND PLUGS
JACK SCHEMATICS
JACK SCHEMATICS
JACK SCHEMATICS
WIRE-WRAPPING TERMINATIONS
Switchcraft can build complete Jack Panel Assemblies with
jacks, lamp jacks and switches with wire-wrapping terminals. If
desired, components with solder lugs and wire-wrapping
terminals can be installed in the same assembly.
WIRE-WRAPPING TERMINAL DESIGN
Jack springs with integral wire-wrapping terminals are made of
special copper alloy for maximum work-life with excellent
resistance to corrosion. Shank of terminal accommodates a
maximum of three wire connections. Tini-Telephone
jacks, lamp jacks and switches with wire-wrapping terminals
have slightly higher stack due to greater spacing required for
wrapping tool access. Actuator springs and ground lug
terminals are .704" long by .060" wide.
NOTE: See tables for jack/plug mating data
JACK MATING DATA
Single closed circuit.
Isolated switching–
“make” before “break”
circuit. (J4-1D).
Tip closed; ring closed
circuits. Isolated
switching–“break”
before “make” circuit.
Double closed circuit.
Isolated switching–
One “make” and one
“break” circuit.
Tip closed; ring open
circuits. Isolated
switching–two “make”
circuits and one “break”
circuit. (J10-2A-1B).
Double closed circuit.
Separate sleeve
“break” circuit.
Tip closed; ring open
circuits. Isolated
switching–One
“make” circuit.
DIMENSIONS ARE FOR REFERENCE ONLY
®
phone
Single open (tip)
circuit and single closed
(ring) circuit. (J9).
Single closed circuit.
Isolated switching–
Two “make” circuits.
Double closed circuit.
Isolated switching–
Two “make” circuits.
WIRE-WRAPPING CONNECTIONS
Use the chart below as a guide to recommended tools to
be used with varying terminal thickness and wire gauges.
SPECIFYING NOTE: Due to assembly variations containing components
(solder lugs, wire-wrapping terminals, or both), these Jack Panel
Assemblies are available on special order only. Contact Switchcraft.
.020 thru .032
.016
.016 thru .032
Thickness
Terminal
(Inches)
Note: Contact your Switchcraft Representative for price and delivery
(mm)
Inch
Double jack,
2-conductors on each
side. Tip circuits cross
shunted; common
sleeve. (J12).
Single open circuit.
Isolated switching–
Two “make” circuits.
Double open circuit.
Isolated switching–
“break” before
“make” circuit.
Gauge
22 & 24
Wire
24
26
PHONE: 773 792 - 2700
Use with 14B1-A
® Registered trademark of Switchcraft, Inc.
Wrapping Bit
(Gardner-Denver Co. Part Numbers)
Recommended Wire-Wrapping Tool
500131
500131
37006
Single open circuit–
“make” before
“break”. (J11).
Double open circuit.
Isolated switching–
One “make” and one
“break” circuit.
Wrapping Tool
17611-2
Sleeve
18840
18840