KMSC7118VM1200 Freescale Semiconductor, KMSC7118VM1200 Datasheet - Page 46

• Manufacturer Part Number: KMSC7118VM1200
• Description: DSP 16BIT W/DDR CTRLR 400-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MSC711x StarCorer
• Type: Fixed Pointr

Specifications of KMSC7118VM1200

• Interface: Host Interface, I²C, UART
• Clock Rate: 300MHz
• Non-volatile Memory: ROM (8 kB)
• On-chip Ram: 464kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: *
• Package / Case: 400-MAPBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Hardware Design Considerations
3.2.3
Each power supply pin (
should be provided with a low-impedance path to ground. The power supply pins drive distinct groups of logic on the device.
The MSC7118
associated printed circuit traces connecting to device power pins and
lead. A minimum four-layer board that employs two inner layers as power and
for DDR Controller power guidelines.
3.2.4
Both the I/O voltage and core voltage should be decoupled for switching noise. For I/O decoupling, use standard capacitor
values of 0.01 μF for every two to three voltage pins. For core voltage decoupling, use two levels of decoupling. The first level
should consist of a 0.01 µF high frequency capacitor with low effective series resistance (ESR) and effective series inductance
(ESL) for every two to three voltage pins. The second decoupling level should consist of two bulk/tantalum decoupling
capacitors, one 10 μF and one 47 μF, (with low ESR and ESL) mounted as closely as possible to the MSC7118 voltage pins.
Additionally, the maximum drop between the power supply and the DSP device should be 15 mV at 1 A.
3.2.5
The MSC7118
power supplied to this pin should be filtered with capacitors that have low and high frequency filtering characteristics.
can be connected to V
shown in Figure 31 is recommended. The PLL loop filter should be placed as closely as possible to the
located on the outside edge of the silicon package) to minimize noise coupled from nearby circuits.The 0.01 µF capacitor should
be closest to
should be kept short.
3.2.6
You can reduce power consumption in your design by controlling the power consumption of the following regions of the device:
For details, see the “Clocks and Power Management” chapter of the MSC711x Reference Manual.
46
•
•
•
•
Extended core. Use the SC1400 Stop and Wait modes by issuing a stop or wait instruction.
Clock synthesis module. Disable the PLL, timer, watchdog, or DDR clocks or disable the
AHB subsystem. Freeze or shut down the AHB subsystem using the GPSCTL[XBR_HRQ] bit.
Peripheral subsystem. Halt the individual on-device peripherals such as the DDR memory controller, HDI16, TDM,
UART, I
V
Power Planes
Decoupling
PLL Power Supply Filtering
DDPLL
Power Consumption
V
V
DDC
DDPLL
2
C, and timer modules.
, followed by the 0.1 µF capacitor, the 10 µF capacitor, and finally the 2-Ω resistor to
power supply pins should be bypassed to ground using decoupling capacitors. The capacitor leads and
DDC
power signal provides power to the clock generation PLL. To ensure stability of the internal clock, the
V
DDC
MSC7118 Low-Cost 16-bit DSP with DDR Controller Data Sheet, Rev. 7
through a 2 Ω resistor. V
,
V
DDM,
V
DDC
and
Figure 31. PLL Power Supply Filter Circuits
V
DDIO
2
Ω
) should have a low-impedance path to the board power supply. Each
SSPLL
10 µF
can be tied directly to the
GND
0.1 µF 0.01 µF
should be kept to less than half an inch per capacitor
GND
GND
V
planes is recommended. See Section 3.5
DDPLL
plane. A circuit similar to the one
CLKO
Freescale Semiconductor
V
DDPLL
pin.
V
DDC
pin (which are
. These traces
GND
V
DDPLL
pin